Offshoreonly.com - Search Results
Offshoreonly.com

Go Back  Offshoreonly.com > Search Forums
Reload this Page >

Search Results

Register
FAQ
Calendar
Today's Posts
Search
Vendor Directory
Notices
 
Page 1 of 2
1
2
Search: Posts Made By: jerosejr
Showing results 1 to 25 of 50
Search took 0.00 seconds.
Forum: Swap Shop
04-26-2010, 05:32 PM
Replies: 24
Views: 7,233
Posted By jerosejr

I might be interested. Please give me a call at...

I might be interested. Please give me a call at 228-385-1650
Jim Rose
Forum: General Q & A
05-02-2007, 08:40 PM
Replies: 4
Views: 1,397
Posted By jerosejr

Ok, I'll do it myself.

Ok, I'll do it myself.
Forum: General Q & A
05-01-2007, 06:30 PM
Replies: 4
Views: 1,397
Posted By jerosejr

This setup is on Ebay for $1300. ...

This setup is on Ebay for $1300.

http://cgi.ebay.com/ebaymotors/New-454-GM-Engine-Assembly-GM-V8-454-Engine-Gen-VI-V8_W0QQitemZ150117364312QQihZ005QQcategoryZ50442QQrdZ1QQcmdZViewItem

That...
Forum: General Q & A
05-01-2007, 04:51 PM
Replies: 4
Views: 1,397
Posted By jerosejr

Please, help me build new engines.

I have a 1973 33' Cary twin inboard. I now have 1987 454 MIE 340 HP but the 2-bolt blocks are trash.

I'm thinking about this:
GM block casting number 10237297 (L29 on Mortec)
GM Cylinder Head...
Forum: General Q & A
04-27-2007, 09:11 PM
Replies: 5
Views: 27,700
Posted By jerosejr

Is this confirmed because there are a lot of...

Is this confirmed because there are a lot of engines for sale on OSO, Ebay, etc that have a serial number in this range and people are claiming 400 HP, probably because they figure that a Gen VI with...
Forum: General Q & A
04-27-2007, 05:38 PM
Replies: 5
Views: 27,700
Posted By jerosejr

How can these engines have different part number...

How can these engines have different part number for heads but have the same intake?
Forum: General Q & A
04-26-2007, 08:23 PM
Replies: 5
Views: 27,700
Posted By jerosejr

The part numbers for the 7.4 MIE MPI are: ...

The part numbers for the 7.4 MIE MPI are:
Crank.............429-811551
Head...............938827656
Intake.............805233A6

The numbers for the 454 Mag MPI are:...
Forum: General Q & A
04-26-2007, 05:42 PM
Replies: 5
Views: 27,700
Posted By jerosejr

Mercruiser 454 or 7.4 Serial numbers

On StemtoStern.com, or Mercruiserparts.com, or other parts lookup websites, there is a range of serial numbers from about 0f800000 to 0k999999.

If you were looking at stern drive big blocks, these...
Forum: General Q & A
04-09-2007, 03:53 PM
Replies: 2
Views: 805
Posted By jerosejr

Name, Phone, Kenner, Louisiana engine builder

What is the name and phone of the engine builder in Kenner or Metairie, Louisiana?
Jim Rose
Biloxi, MS
Forum: General Q & A
04-01-2007, 10:17 PM
Replies: 9
Views: 1,793
Posted By jerosejr

Make more power at 3500 rpm. swing a larger...

Make more power at 3500 rpm.
swing a larger prop in an inboard application.
Forum: General Q & A
04-01-2007, 09:40 PM
Replies: 9
Views: 1,793
Posted By jerosejr

If the 454 Mag is MPI, after the bore and stroke...

If the 454 Mag is MPI, after the bore and stroke to 496, can the ecu be reprogremmed for the new size?
Forum: General Q & A
04-01-2007, 09:09 PM
Replies: 9
Views: 1,793
Posted By jerosejr

Got it !!!!!!!!!!!!! Thanks guys.

Got it !!!!!!!!!!!!!
Thanks guys.
Forum: General Q & A
04-01-2007, 08:10 PM
Replies: 9
Views: 1,793
Posted By jerosejr

OOPS Meant to say 4.250. So I guess the...

OOPS
Meant to say 4.250.

So I guess the article mentioned above says that it can be done.
Has anyone ever done this? Is it too much bore?
Would it be better to go the 496 route?
Forum: General Q & A
04-01-2007, 07:09 PM
Replies: 9
Views: 1,793
Posted By jerosejr

Boring 454 Mag-385 .220 over

A 454 Mag 385 hp has all the steel internals of a 502 mag.
The diameter of the 454 is 1.250
The diameter of the 502 is 1.470
The difference is 0.220 (220 thousandths)
Can this be done? and then...
Forum: Classic Offshore
01-07-2007, 10:34 AM
Replies: 3
Views: 1,793
Posted By jerosejr

Alton Cary, any info?????

I own a Cary 33SS hull. I,ve been told this hull was the "first" Cigarette boat.
Does anyone have info on Mr Cary and his history, his hulls, his association with Don Arownow, etc.???
Jim Rose,...
Forum: General Boating Discussion
03-13-2006, 09:18 PM
Replies: 38
Views: 5,586
Posted By jerosejr

Re: what is the going $$ for 502 MPIs

Dean, you gonna sell those 502's or what?
Please let me (us) know.
Forum: General Q & A
03-10-2006, 05:02 PM
Replies: 5
Views: 851
Posted By jerosejr

Re: After Katrina, is MPI any good !!

Sorry about the confusion guys. I only had the EFI stuff in the garage (intake, computer, wires, VST, fuel rail, etc).
Forum: General Q & A
03-10-2006, 09:41 AM
Replies: 5
Views: 851
Posted By jerosejr

After Katrina, is MPI any good !!

Had 19 feet of water where I live. Garage flooded to the ceiling.

In that garage, I had two 502 MPI's with the VST, intakes, rails, computers, wires, etc. (not connected to a battery)

Cleaned...
Forum: General Boating Discussion
03-07-2006, 08:05 AM
Replies: 38
Views: 5,586
Posted By jerosejr

Re: what is the going $$ for 502 MPIs

Dean
Jim Rose, Biloxi, MS, here. I'm restoring a 1973 33' Cary (that actually survived Katrina in the water) and need two 502's. Please let me know your status at 800-545-4307 or...
Forum: General Q & A
08-18-2005, 08:34 AM
Replies: 9
Views: 6,582
Posted By jerosejr

Re: 454 mag carb to EFI swap?

With todays gas prices, has anyone seen better fuel efficiency with MPI ove carbs?
Forum: General Q & A
06-01-2005, 08:05 AM
Replies: 4
Views: 14,853
Posted By jerosejr

Re: Will a 454 Mark IV transfer to Gen VI?

RE: the oil adapter
I read here somewhere that the oil adapter for a GenVI has a different checkvalve or something. Anybody know about this?
Forum: Detailing, Painting, & Fiberglass
05-24-2005, 09:56 PM
Replies: 9
Views: 1,500
Posted By jerosejr

Re: Motor paint

Somewhere on Mercruisers website, maybe the tech stuff, they give their formula for repainting an outdrive. I would think this is good enough for the engine.
Forum: Detailing, Painting, & Fiberglass
04-25-2005, 09:13 PM
Replies: 7
Views: 1,863
Posted By jerosejr

Re: Rust on Gel Coat .......

Alumabrite. This is a basic (not acidic) solution that will dissolve rust stains before your eyes.
Caution: Do not put on aluminum or stainless. This stuff was made to "etch" metals before priming....
Forum: General Q & A
04-09-2005, 09:34 AM
Replies: 5
Views: 2,044
Posted By jerosejr

Re: Anyone have a MEFI3 ECM For Sale?

Theres one on Ebay rite now
Forum: General Q & A
04-03-2005, 10:35 AM
Replies: 1
Views: 2,025
Posted By jerosejr

Cool Fuel vs. VST

Building stock MPI 502's to replace 454's.
When selecting the MPI to use, which one does everybody prefer- the VST versions or the Cool Fuel versions? Why?
Showing results 1 to 25 of 50
 
Page 1 of 2
1
2


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.