Offshoreonly.com - Search Results
Offshoreonly.com

Go Back  Offshoreonly.com > Search Forums
Reload this Page >

Search Results

Register
FAQ
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: estonian
Showing results 1 to 12 of 12
Search took 0.00 seconds.
Forum: General Q & A
09-03-2008, 06:23 AM
Replies: 1
Views: 1,586
Posted By estonian

Pushrod length

I want to upgrade comp magnum roller tip 1.52 rocker arms on my sbc 383 with crane gold 1.6's.
Will the pushrod length (7.200, hydro roller lifters) remain the same? Plan to upgrade the pushrods as...
Forum: General Q & A
01-14-2008, 11:52 AM
Replies: 8
Views: 9,695
Posted By estonian

Thanks!

Thanks!
Forum: General Q & A
01-05-2008, 09:06 AM
Replies: 8
Views: 9,695
Posted By estonian

Rhoads lifters

I had pump up problem on my SBC 383 with CompCam 850 lifters last season (max rpm 6500). Do you have experience with Rhoads V-MAX Super Lube Roller lifters (are they that good at idle and low rpm as...
Forum: General Q & A
07-21-2006, 12:37 PM
Replies: 4
Views: 962
Posted By estonian

hydraulic lifter

Hi ! I have hydraulic roller lifters and high volume oil pump on my engine. I use Motul 300V Copetition 15W 50 oil and oil pressure is 70 PSI (idle) to 90 PSI (full throtle). Is there a risk that...
Forum: General Q & A
04-10-2006, 12:44 PM
Replies: 2
Views: 1,148
Posted By estonian

Sparkplugs

What sparkplugs to use (brand, model)? I have 383 with comresion ratio 9.8 and max RPM 6000, naturaly aspirated, standard Crusader ignition (Prestolite distributor) .
We have NGK, Bosch, AC and...
Forum: General Q & A
10-13-2005, 02:07 PM
Replies: 35
Views: 23,545
Posted By estonian

Re: Small block 383 build-up

I've been surfing arround a lot and I think I've found what I need. Do you have any experience with Allied Motors (strokerkits.com). They have set called Complete 383 Stroker minus the block...
Forum: General Q & A
09-20-2005, 10:46 AM
Replies: 35
Views: 23,545
Posted By estonian

Re: Small block 383 build-up

Thank you all for lots of usefull information. Finally I think I'm getting the picture and I will use Scat forged rotating assembly kit (forged crank, forged I-beam rods, forged SRP pistons). But...
Forum: General Q & A
09-18-2005, 12:05 PM
Replies: 35
Views: 23,545
Posted By estonian

Re: Small block 383 build-up

Thanks! Do you have 2- or 4-bolt main caps? What exhaust do you have?
P.S. What prop are you using?
Forum: General Q & A
09-18-2005, 08:55 AM
Replies: 35
Views: 23,545
Posted By estonian

Small block 383 build-up

Hi! I'm Estonian (Europe) boat racer with experience in circuit racing. We are just starting up with offshore races here. I am racing (our national class)with 23' boat with 350 CID Crusader. For next...
Forum: Prop Talk
09-18-2005, 02:15 AM
Replies: 10
Views: 2,507
Posted By estonian

Re: Bravo I prop

The boat is self-made 23' deep V (28 degrees). Weight is 3000 lbs. Engine is Crusader 350 (270-290 HP). Sterndrive is Volvo Penta 280 (with self-made propshaft to fit MerCruiser props). You can see...
Forum: Prop Talk
09-16-2005, 06:42 AM
Replies: 10
Views: 2,507
Posted By estonian

Re: Bravo I prop

Thanks for the answer. The prop is stock.
Forum: Prop Talk
09-16-2005, 02:24 AM
Replies: 10
Views: 2,507
Posted By estonian

Bravo I prop

Hi! I just got new Bravo I 26P prop. Before I had Mirage Plus 25. With Mirage I had max speed 61 mph (4800 RPM, gear ratio 1,63). With Bravo RPM remaned the same, but max speed was 58 mph. I measured...
Showing results 1 to 12 of 12


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.