Offshoreonly.com - Search Results
Offshoreonly.com

Go Back  Offshoreonly.com > Search Forums
Reload this Page >

Search Results

Register
FAQ
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: lloyd
Showing results 1 to 14 of 14
Search took 0.00 seconds.
Forum: General Q & A
06-06-2005, 05:45 PM
Replies: 10
Views: 3,747
Posted By lloyd

Re: LS 1 BATBOAT PROJECT by Mesa

Here is a company in New Zeland that has marine manifolds for the LS1.http://www.waspaust.co.nz/Chev6.htm
Forum: General Q & A
04-06-2005, 04:23 PM
Replies: 46
Views: 14,779
Posted By lloyd

Re: Piston Sprayers

The new Cadillac STS V has piston sprayers also. They are the type that spray oil on the underside of the piston crown.
Forum: General Q & A
10-18-2004, 10:22 AM
Replies: 14
Views: 3,224
Posted By lloyd

Re: Pyrometers

I have run EGT's in snowmobiles for years. They are only useful as a tool for determining problems or correcting setup if you take your boat to somewhere with substantial changes in altitude or temp....
Forum: General Q & A
09-28-2004, 12:10 PM
Replies: 7
Views: 1,238
Posted By lloyd

Re: propeller vs rpm question

The ignition is a Crane unit with the rev limiter set at 6000rpm. We used the ignition during dyno testing. The tach is a brand new Autometer and I have hooked up my Mac Tools scan tool to verify the...
Forum: General Q & A
09-27-2004, 07:33 PM
Replies: 7
Views: 1,238
Posted By lloyd

Question propeller vs rpm question

I am trying to help my brother with his 22' regal/velocity. I am confused with the way the boat has reacted to the three propellers we have tried so far. First prop is a 26P Bravo 1 4 blade. Strong...
Forum: General Q & A
09-09-2004, 04:55 PM
Replies: 12
Views: 3,193
Posted By lloyd

Re: Plumbing a mech fuel presure gage?

You are crazy to put a mechanical fuel pressure gage in. There will not be ant issues with false/inaccurate readings from an electric gage. I am willing to bet big bucks that your insurance would be...
Forum: General Q & A
09-07-2004, 01:34 PM
Replies: 18
Views: 2,556
Posted By lloyd

Re: Fed up with Dominator, any ideas on where I can send it ?

Had my 850 done by Dean Nickerson. When I had the engine dynoed the dyno operator told me that it had one of the smoothest fuel curves he had seen. I had some tuning issues (mine not theirs) and they...
Forum: General Q & A
08-21-2004, 11:21 AM
Replies: 62
Views: 25,922
Posted By lloyd

Re: Getting the jetting right -500hp - 454

Check out the Innovate Motorsports web sight. Their air fuel meter will allow you to not only do your jetting but to dial in your entire fuel curve by adjusting your high and low speed air bleeds. I...
Forum: General Q & A
08-19-2004, 02:01 PM
Replies: 23
Views: 26,218
Posted By lloyd

Re: Power valves for Holley carbs

I am jetting a carb that was built by Nickerson Performance. When I talked to them about power valve selection I was told to cruise at 3800 rpm, take a vacuum reading and that was the power valve to...
Forum: Velocity
06-29-2004, 01:02 PM
Replies: 45
Views: 32,888
Posted By lloyd

Re: 88 22' Velocity-> Good, Bad, Indifferent?

My brother has a Velocity/Regal just like your picture. We live in Vancouver BC Canada so he runs 90% in the ocean.This is a very solid boat in rough chop. I think they are slightly bow heavy but the...
Forum: General Q & A
06-28-2004, 04:33 PM
Replies: 23
Views: 4,201
Posted By lloyd

Re: Need Jetting Advice

My fuel pressure did not show a drop on the gage either.
Forum: General Q & A
06-28-2004, 01:30 PM
Replies: 23
Views: 4,201
Posted By lloyd

Re: Need Jetting Advice

I think you are wasting your time with jetting until you fix the fuel supply side. I had a drag boat that had the same problem. I was up to 140's and still flattened out.I went up to 9/16 line...
Forum: General Boating Discussion
12-08-2003, 10:18 AM
Replies: 18
Views: 4,827
Posted By lloyd

I'm a Canadian dealer.If you are not sure then...

I'm a Canadian dealer.If you are not sure then wait till July or August of '04.The new STS will be out with rear wheel drive and the series 2 Northstar That should give you an additional choice.
Forum: General Q & A
06-26-2003, 10:41 AM
Replies: 11
Views: 18,587
Posted By lloyd

Hi-Tek Marine in Australia makes small block ford...

Hi-Tek Marine in Australia makes small block ford shorty wet headers
Showing results 1 to 14 of 14


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.