Offshoreonly.com - Search Results
Offshoreonly.com

Go Back  Offshoreonly.com > Search Forums
Reload this Page >

Search Results

Register
FAQ
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: tho145
Showing results 1 to 9 of 9
Search took 0.00 seconds.
Forum: Ilmor High Performance Marine
06-16-2011, 07:48 PM
Replies: 12
Views: 5,067
Posted By tho145

If you have room for the 650, you'll have room...

If you have room for the 650, you'll have room for the 625. The air filter extends back ~1.5-2" further on the 650 than it does on the 625, the headers are a little different for the Gen III as well...
Forum: General Boating Discussion
05-12-2010, 11:56 AM
Replies: 212
Views: 46,657
Posted By tho145

Yep, definitely the coolest thing I've seen all...

Yep, definitely the coolest thing I've seen all day
Forum: General Boating Discussion
12-22-2009, 01:41 PM
Replies: 18
Views: 2,033
Posted By tho145

Simply Custom 1732 Eureka Wyandotte, Mi ...

Simply Custom

1732 Eureka
Wyandotte, Mi

734-558-4051
Forum: Fountain
11-17-2009, 11:53 AM
Replies: 9
Views: 2,102
Posted By tho145

From the inside of the transom to the front of...

From the inside of the transom to the front of the 650 is ~43".
Forum: Baja
07-15-2009, 12:10 PM
Replies: 12
Views: 3,218
Posted By tho145

"I'm guessing you've never seen the engine room...

"I'm guessing you've never seen the engine room in a 29 Outlaw."

Sadly I have not. I was just trying to point out that they weren't that much longer if you were going to run a stagger, that's...
Forum: Baja
07-15-2009, 08:54 AM
Replies: 12
Views: 3,218
Posted By tho145

On a 36" stagger with Indy's, the Ilmors should...

On a 36" stagger with Indy's, the Ilmors should only be 2 5/8" longer than a standard 36"stagger with 700s'. Depending on what centers you run you might be able to go shorter on the stagger distance.
Forum: General Boating Discussion
06-10-2009, 01:40 PM
Replies: 26
Views: 4,709
Posted By tho145

I haven't used many of the CAM specific programs...

I haven't used many of the CAM specific programs but....

Autocad will get you through most 2d.

For 3d, I would go Solidworks, Inventor, or Unigraphix. You can generate 2d from any of those...
Forum: General Q & A
03-25-2009, 01:41 PM
Replies: 18
Views: 1,807
Posted By tho145

Technique does a good job as well. Here's another...

Technique does a good job as well. Here's another out of Auburn Hills:

http://www.rpparts.com
Forum: General Q & A
03-25-2009, 12:01 PM
Replies: 18
Views: 1,807
Posted By tho145

Check out a company called Synergeering, they're...

Check out a company called Synergeering, they're out of farmington hills.

(313) 215-3076

They may be able to help.
Showing results 1 to 9 of 9


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.