Offshoreonly.com - Search Results
Offshoreonly.com

Go Back  Offshoreonly.com > Search Forums
Reload this Page >

Search Results

Register
FAQ
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: MILD THUNDER
Showing results 1 to 9 of 9
Search took 0.00 seconds.
Forum: General Q & A
10-27-2016, 06:10 PM
Replies: 55
Views: 16,552
Posted By MILD THUNDER

What gaskets did you use back in the day that...

What gaskets did you use back in the day that were .060 thick? I ran .066 cometic on one of my engines where the piston was out of the hole quite a bit, but i don't remember anyone making gaskets...
Forum: General Q & A
10-27-2016, 06:06 PM
Replies: 55
Views: 16,552
Posted By MILD THUNDER

Around here 500-700 per day.

Around here 500-700 per day.
Forum: General Q & A
10-27-2016, 01:38 PM
Replies: 55
Views: 16,552
Posted By MILD THUNDER

For sure. It still is what it is though. It be...

For sure. It still is what it is though. It be pretty cool to see what a non intercooled procharger does, vs a non intercooled roots. I know what the temps are with a non intercooled carb'd 1071...
Forum: General Q & A
10-26-2016, 10:55 PM
Replies: 55
Views: 16,552
Posted By MILD THUNDER

You won't get .018 above the deck under operating...

You won't get .018 above the deck under operating conditions. The piston grows when its hot.

With a .051 gasket, and even with the piston rock at max, you'd still have .033 of clearance. Once the...
Forum: General Q & A
10-26-2016, 10:31 PM
Replies: 55
Views: 16,552
Posted By MILD THUNDER

I noticed those IAT temperatures on your dyno...

I noticed those IAT temperatures on your dyno sheet. Pretty cool info. I always thought the prochargers were soooooo much cooler running , and how you could run way more boost than a roots. Those IAT...
Forum: General Q & A
10-26-2016, 02:19 PM
Replies: 55
Views: 16,552
Posted By MILD THUNDER

I assumed it was a howards grind when you gave...

I assumed it was a howards grind when you gave those specs.

Id go with the .051 gaskets. It wont hurt a thing , and you wont be knocking the carbon off the quench pad of the piston .
Forum: General Q & A
10-26-2016, 12:48 PM
Replies: 55
Views: 16,552
Posted By MILD THUNDER

I like the 651 cam in a blower motor. Ive seen it...

I like the 651 cam in a blower motor. Ive seen it used in a NA 540 with afr cnc heads, and wasnt all that impressed. It didnt pull quite as high without the blower helping,

Reason i say id go...
Forum: General Q & A
10-26-2016, 08:05 AM
Replies: 55
Views: 16,552
Posted By MILD THUNDER

In a bbc marine build with steel rods, i...

In a bbc marine build with steel rods, i personally would go with .040 as a minimum, .060 as a maximum for an NA build.

If the cam you posted, and the 651 were my only two choices, i would go...
Forum: General Q & A
10-26-2016, 06:22 AM
Replies: 55
Views: 16,552
Posted By MILD THUNDER

I'd go with a .051 gasket if the piston is out of...

I'd go with a .051 gasket if the piston is out of the hole .005.
Showing results 1 to 9 of 9


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.