Offshoreonly.com - Search Results
Offshoreonly.com

Go Back  Offshoreonly.com > Search Forums
Reload this Page >

Search Results

Register
FAQ
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: schiada.cat
Showing results 1 to 11 of 11
Search took 0.00 seconds; generated 94 minute(s) ago.
Forum: Swap Shop
05-08-2026, 12:37 AM
Replies: 1
Trs
Views: 272
Posted By schiada.cat

Trs

What state are these units located in?
Forum: Swap Shop
05-08-2026, 12:25 AM
Replies: 8
Views: 1,209
Posted By schiada.cat

Prop spline size

Do these drives have the same prop splines as the TRS drive?
Forum: Swap Shop
05-08-2026, 12:09 AM
Replies: 8
Views: 1,209
Posted By schiada.cat

Konrad parts

What else will be needed to replace my TRS drives with these units?
Forum: General Q & A
04-11-2009, 11:30 PM
Replies: 1
Views: 728
Posted By schiada.cat

who makes fuel cells?

One of my fuel safe fuel cells is starting to get some exterior cracks.I replaced the other one last year (kevlar and foam type) and was not thrilled with their service..who else makes them? approx...
Forum: General Q & A
12-25-2008, 01:28 PM
Replies: 7
Views: 1,958
Posted By schiada.cat

does inward mean from the top of the prop .. the...

does inward mean from the top of the prop .. the starboard spins counterclockwise and the port clockwise?
Forum: General Q & A
12-25-2008, 03:40 AM
Replies: 7
Views: 1,958
Posted By schiada.cat

Bow Lift..prop rotation

What is the correct direction of prop rotation to get the most bow lift on counter rotating drives and is it the same for V hulls and Cats?
Will more bow lift cause quicker wear of the drives or...
Forum: General Q & A
12-11-2008, 10:32 AM
Replies: 12
Views: 2,347
Posted By schiada.cat

compared your photo to what we need . Those are...

compared your photo to what we need . Those are for the smaller blowers...the ones we need are about the same size but have a different offset and are a one piece casting which is thicker. Yours...
Forum: General Q & A
12-10-2008, 12:45 PM
Replies: 12
Views: 2,347
Posted By schiada.cat

we have the standard intake manifold for the 250...

we have the standard intake manifold for the 250 on it now, this is just an extension to adapt the stock mercusier cooling hoses to it...but if we cant find the extension we might have to just go to...
Forum: General Q & A
12-10-2008, 10:51 AM
Replies: 12
Views: 2,347
Posted By schiada.cat

picture

If you can post a picture that would help, I will try to get one but I am out on the road this week.
Its about 12 inches long 5 inches wide with normal water neck openings at each end. It is shaped...
Forum: General Q & A
12-10-2008, 10:01 AM
Replies: 12
Views: 2,347
Posted By schiada.cat

water neck B&M

The part we need comes from the front of the B&M manifold and connects the Mercrusier cast iron part (thermostat /housing hose manifold from mercrusier to the B&M manifold)
The part that was...
Forum: General Q & A
12-10-2008, 12:36 AM
Replies: 12
Views: 2,347
Posted By schiada.cat

Unhappy is there a replacement made for B&M/Merc water neck

The water neck thermostat housing extension has rotted thru on my B&M 250 superchargers..its the one that works with the stock Mercrusier cooling system that came on the 420 HP 454 Checy Big Block.....
Showing results 1 to 11 of 11


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.