selling my 32' A/T...
06-29-2009 | 07:23 AM
#1
Thread Starter
Registered
Joined: Oct 2000
Posts: 4,541
Likes: 107
From: Western Michigan
selling my 32' A/T...
My 1990 32' Active Thunder is for sale....with or without power, Marine Marchine dual ram external racing steering with stainless steel wing plates, K-Planes, trim/tab indicators, cockpit cover and full length water proof storage/mooring/traveling cover, Stellings extension boxes available. Also has a Tri-axle Eagle trailer with drive guard. Rewired last year with all heat shrink connectors, new navigation lights, new cabin stereo/speakers.
Replaced transom, stringers and engine compartment floor in 2003---it is better and stronger now vs the way it was previously. Fresh/rebuilt this year Bravo XR's by Mr. Gadgets with zero hours.
The structure, electrical and engines are all excellent----but the boat needs upholstry in cockpit and on the engine hatch. I have been through a lot with this boat---it's a very good boat....just needs some TLC.
Lots of options available on the boat. It is a great running boat!
Reason for selling???----I am currently looking for a larger boat.
Will be posting photos soon.
Replaced transom, stringers and engine compartment floor in 2003---it is better and stronger now vs the way it was previously. Fresh/rebuilt this year Bravo XR's by Mr. Gadgets with zero hours.
The structure, electrical and engines are all excellent----but the boat needs upholstry in cockpit and on the engine hatch. I have been through a lot with this boat---it's a very good boat....just needs some TLC.
Lots of options available on the boat. It is a great running boat!
Reason for selling???----I am currently looking for a larger boat.
Will be posting photos soon.
Last edited by KAAMA; 02-22-2010 at 09:06 PM. Reason: mis-spelled some words
07-11-2009 | 03:23 PM
#6
Registered
Joined: Sep 2005
Posts: 252
Likes: 0
From: West Michigan
Hey Mark! Hope all is well! Sorry to hear your letting that boat go!
That's one awesome piece of machinery you're selling!!! I've always been impressed by the way those engines run and how efficient your boat is!!!
In case you decide not to run it this summer, give me a call, I'd be happy to take you out on mine!
Jeff
That's one awesome piece of machinery you're selling!!! I've always been impressed by the way those engines run and how efficient your boat is!!!
In case you decide not to run it this summer, give me a call, I'd be happy to take you out on mine!
Jeff
01-19-2010 | 02:48 PM
#9
Thread Starter
Registered
Joined: Oct 2000
Posts: 4,541
Likes: 107
From: Western Michigan
New 482cid engines dyno photos...
These engines are going in my 32' AT that is up for sale....and were built by Dave Wesseldyk at WESCO in Jension, MI just outside of Grand Rapids.
New blocks, 4.24", new rotating assemblies, rings, bearings, stainless valves, Isky valve springs, 10* retainers/locks, hydraulic cams/lifters, Intake manifolds, Stainless steel 1.7 roller rocker arms, pushrods, balancers, oil pumps, Roll Master timging chain sets, new Glenwood Marine timing chain covers and pumps....most all internal components are new.
Engines dyno'd at 509hp and 561tq....
New blocks, 4.24", new rotating assemblies, rings, bearings, stainless valves, Isky valve springs, 10* retainers/locks, hydraulic cams/lifters, Intake manifolds, Stainless steel 1.7 roller rocker arms, pushrods, balancers, oil pumps, Roll Master timging chain sets, new Glenwood Marine timing chain covers and pumps....most all internal components are new.
Engines dyno'd at 509hp and 561tq....
