32 Skater Restoration O/b
#1
Registered
Thread Starter
Join Date: Feb 2010
Posts: 974
Likes: 0
Received 0 Likes
on
0 Posts
32 Skater Restoration O/b
Here are Updated Pics . There Are A Few Things Like Hatch , Console And Arched Shifter Cover I Made Molds For And Made My Own Fiberglass Parts . Sure I Could Call Skater And Order A Console For $ But Didnt Like Anything Made ( Wanted One That Goes Under Dash ) So I Made One . The Shifter Cover They Make Is Alum And Snaps Together ( Really Mickey Mouse ) So I Made Composite Part With Built In Threads . The Hatch Is One Off With Built In Cooler , Flush Lids With Custom Hidden Hinges I Made In House ( Zero Exposed Screws )
Last edited by KEVLARKAT32; 01-31-2011 at 11:28 PM.
#2
Registered
Thread Starter
Join Date: Feb 2010
Posts: 974
Likes: 0
Received 0 Likes
on
0 Posts
Pics Of Rear Cabin , Skater Logo Cut From 3/8 Figerglass And Will Worked Down To 1/8 High And Bonded To Hatch And Body Work And When Done Will Look Like It Was Always There. When I layed up hatch I buried 3/8 alum 4x 6 plates in layup and cannot be seen , this way all I did was tap holes for hinges with zero visible hardware . I also incorporated small gas strut on hinge and is almost unseen when opened .
Last edited by KEVLARKAT32; 01-31-2011 at 11:34 PM.
#3
Registered
Thread Starter
Join Date: Feb 2010
Posts: 974
Likes: 0
Received 0 Likes
on
0 Posts
More Pics. I wanted to keep dash simple and un-cluttered , key swithes will be under dash on angle bracket, I hate to see them , engine kills will be on side of console I see other Skaters with every inch of of dash cluttered with somthing , keep it simple !! To the left if a grab handle and as of now Skater logo will be on left side
Last edited by KEVLARKAT32; 02-01-2011 at 07:22 AM.
#4
Registered
Larry, luv the metalic dash, the invisble hinge and the cooler..
But I think the raised-lettering on the Skater logo tops it all, don't sand away too much of it...that's the first I've ever seen...
But I think the raised-lettering on the Skater logo tops it all, don't sand away too much of it...that's the first I've ever seen...
#6
Registered
Larry, can you take pics of the quarter hatch in closed position?
I wanna see how flat it is and the invisible hinges.
Show your designs to Peter, I bet he'd be very interested. Along with the raised-lettering Skater logo.
I wanna see how flat it is and the invisible hinges.
Show your designs to Peter, I bet he'd be very interested. Along with the raised-lettering Skater logo.
#7
Registered
iTrader: (3)
Join Date: Dec 2003
Location: Cleveland, OH / Pewaukee, WI
Posts: 5,864
Received 362 Likes
on
207 Posts
Here are Updated Pics . There Are A Few Things Like Hatch , Console And Arched Shifter Cover I Made Molds For And Made My Own Fiberglass Parts . Sure I Could Call Skater And Order A Console For $ But Didnt Like Anything Made ( Wanted One That Goes Under Dash ) So I Made One . The Shifter Cover They Make Is Alum And Snaps Together ( Really Mickey Mouse ) So I Made Composite Part With Built In Threads . The Hatch Is One Off With Built In Cooler , Flush Lids With Custom Hidden Hinges I Made In House ( Zero Exposed Screws )
Jr.
#10
Registered
Nice work!