BBC parts blowout
#1
Registered
Thread Starter
Join Date: Sep 2008
Location: Lubbock, TX
Posts: 306
Likes: 0
Received 0 Likes
on
0 Posts
BBC parts blowout
Most of the stuff in this thread came off a 509 I bought from Mesa Balancing. The motor made 630hp, I have the dyno sheet somewhere but cant find it now. The motor spun a bearing at 10 hours, my fault not the builders. The block I bought to replace it was already bored beyond 4.53 so I could not ude the pistons, and I had a set of merlin heads that went on the new motor. I used a factory GM forged crank so the internal balance flywheel and balancer were not practical to reuse. that is the story with the parts. I did not clean any of this stuff so it kind of looks like sh*t in the pics, but it is all low hours and in good shape. Freshwater use only.
Internal Balance Jegs Harmonic Balancer p/n 555-51615 cost me $220, sell for $70 plus shipping
http://i968.photobucket.com/albums/a...1/IMG_0442.jpg
http://i968.photobucket.com/albums/a...1/IMG_0443.jpg
http://i968.photobucket.com/albums/a...1/IMG_0444.jpg
Billet steel flywheel internal Balance, needs new $23 ring gear, cost me $380, sell for $80 plus shipping
http://i968.photobucket.com/albums/a...1/IMG_0449.jpg
http://i968.photobucket.com/albums/a...1/IMG_0450.jpg
Mercruiser Gen 6 oil pan and windage tray $60
http://i968.photobucket.com/albums/a...1/IMG_0455.jpg
Merlin Intake for 4150 carb, Brass sleeved marine version, sanded paint to change the color, but other wise in great shape, cost $485 from summit, will take $170 plus shipping
http://i968.photobucket.com/albums/a...1/IMG_0447.jpg
http://i968.photobucket.com/albums/a...1/IMG_0448.jpg
Spr forged flat top 4.53 pistons with total seal rings. Less then 10 hours use, very nice set of pistons and rings.P/N139483 Cost me over $600, would like to get $270 plus shipping, includes spiral locks and pins
http://i968.photobucket.com/albums/a...1/IMG_0459.jpg
http://i968.photobucket.com/albums/a...1/IMG_0457.jpg
http://i968.photobucket.com/albums/a...1/IMG_0460.jpg
HP500 heads, setup for hydrailic roller with new spring, Manley super duty powerflow intake and iconel exhaust valves. Light port and bowl work by Mesa Balancing. Ready to run, casting number 12562934. Would like to get $800 plus shipping for the set. Have way more then that in them.
http://i968.photobucket.com/albums/a...1/IMG_0451.jpg
http://i968.photobucket.com/albums/a...1/IMG_0452.jpg
http://i968.photobucket.com/albums/a...1/IMG_0453.jpg
Mark 4 remote oil filter adapter $30 plus shipping
http://i968.photobucket.com/albums/a...1/IMG_0445.jpg
http://i968.photobucket.com/albums/a...1/IMG_0446.jpg
If I am way off base on any of the prices let me know, I do not need this stuff taking up more garage space. I will be happy to email more pics in needed and awnser any questions. I know all this stuff is dirty in the pics, but I have been cleaning motor parts reassembling my motor for 2 mo, and i am tired of scrubbing, all the stuff is in good to great condition.
Internal Balance Jegs Harmonic Balancer p/n 555-51615 cost me $220, sell for $70 plus shipping
http://i968.photobucket.com/albums/a...1/IMG_0442.jpg
http://i968.photobucket.com/albums/a...1/IMG_0443.jpg
http://i968.photobucket.com/albums/a...1/IMG_0444.jpg
Billet steel flywheel internal Balance, needs new $23 ring gear, cost me $380, sell for $80 plus shipping
http://i968.photobucket.com/albums/a...1/IMG_0449.jpg
http://i968.photobucket.com/albums/a...1/IMG_0450.jpg
Mercruiser Gen 6 oil pan and windage tray $60
http://i968.photobucket.com/albums/a...1/IMG_0455.jpg
Merlin Intake for 4150 carb, Brass sleeved marine version, sanded paint to change the color, but other wise in great shape, cost $485 from summit, will take $170 plus shipping
http://i968.photobucket.com/albums/a...1/IMG_0447.jpg
http://i968.photobucket.com/albums/a...1/IMG_0448.jpg
Spr forged flat top 4.53 pistons with total seal rings. Less then 10 hours use, very nice set of pistons and rings.P/N139483 Cost me over $600, would like to get $270 plus shipping, includes spiral locks and pins
http://i968.photobucket.com/albums/a...1/IMG_0459.jpg
http://i968.photobucket.com/albums/a...1/IMG_0457.jpg
http://i968.photobucket.com/albums/a...1/IMG_0460.jpg
HP500 heads, setup for hydrailic roller with new spring, Manley super duty powerflow intake and iconel exhaust valves. Light port and bowl work by Mesa Balancing. Ready to run, casting number 12562934. Would like to get $800 plus shipping for the set. Have way more then that in them.
http://i968.photobucket.com/albums/a...1/IMG_0451.jpg
http://i968.photobucket.com/albums/a...1/IMG_0452.jpg
http://i968.photobucket.com/albums/a...1/IMG_0453.jpg
Mark 4 remote oil filter adapter $30 plus shipping
http://i968.photobucket.com/albums/a...1/IMG_0445.jpg
http://i968.photobucket.com/albums/a...1/IMG_0446.jpg
If I am way off base on any of the prices let me know, I do not need this stuff taking up more garage space. I will be happy to email more pics in needed and awnser any questions. I know all this stuff is dirty in the pics, but I have been cleaning motor parts reassembling my motor for 2 mo, and i am tired of scrubbing, all the stuff is in good to great condition.
Last edited by tx911; 11-02-2009 at 08:16 AM.
#8
Registered
Thread Starter
Join Date: Sep 2008
Location: Lubbock, TX
Posts: 306
Likes: 0
Received 0 Likes
on
0 Posts
I emailed him today at lunch. Sorry it took so long, I ended up getting invited last minute to go hunting so I was out of town the end of the week and the weekend.