Go Back  Offshoreonly.com > Offshoreonly Marketplace > Swap Shop
XR Upper 18" Input shaft >

XR Upper 18" Input shaft

Notices

XR Upper 18" Input shaft

Old 12-17-2020, 11:20 AM
  #1  
253
Platinum Member
Platinum Member
Thread Starter
 
Join Date: Jan 2002
Location: Southern, IL.
Posts: 605
Received 12 Likes on 7 Posts
Default XR Upper 18" Input shaft

XR Upper Input shaft, for ITS ,, the shaft is 18" from end of splines to center of u-joint , oil seal area on the yoke is good cond., u-joints are tight,
$525 . includes shipping in lower 48 states


Last edited by 253; 12-18-2020 at 01:39 PM.
253 is offline  
Old 12-17-2020, 12:22 PM
  #2  
Registered
iTrader: (2)
 
TxHawk's Avatar
 
Join Date: Mar 2003
Location: Dallas
Posts: 3,049
Received 16 Likes on 8 Posts
Default

Is this the ITS input shaft ?
TxHawk is offline  
Old 12-17-2020, 12:47 PM
  #3  
253
Platinum Member
Platinum Member
Thread Starter
 
Join Date: Jan 2002
Location: Southern, IL.
Posts: 605
Received 12 Likes on 7 Posts
Default

I don't know,,,hopefully some here will know
253 is offline  
Old 12-17-2020, 12:52 PM
  #4  
Platinum Member
Platinum Member
iTrader: (6)
 
F-2 Speedy's Avatar
 
Join Date: May 2012
Location: Midwest & T-Rock
Posts: 7,966
Received 782 Likes on 383 Posts
Default

[QUOTE=TxHawk;4769506]Is this the ITS input shaft ?[/QUOTE

Id say yes
F-2 Speedy is online now  
Old 12-17-2020, 12:59 PM
  #5  
253
Platinum Member
Platinum Member
Thread Starter
 
Join Date: Jan 2002
Location: Southern, IL.
Posts: 605
Received 12 Likes on 7 Posts
Default

I recently bought a Mercruiser XR outdrive,, this is the upper shaft that was on it.,,It is in good condition.
253 is offline  
Old 12-17-2020, 01:03 PM
  #6  
Platinum Member
Platinum Member
iTrader: (6)
 
F-2 Speedy's Avatar
 
Join Date: May 2012
Location: Midwest & T-Rock
Posts: 7,966
Received 782 Likes on 383 Posts
Default

if the long one is about 7.5 inches longer then the shorter one, then its ITS, I run them on my boat
F-2 Speedy is online now  
Old 12-17-2020, 03:03 PM
  #7  
253
Platinum Member
Platinum Member
Thread Starter
 
Join Date: Jan 2002
Location: Southern, IL.
Posts: 605
Received 12 Likes on 7 Posts
Default

I measured again,, it is 7 inches longer than a stock Bravo shaft
253 is offline  
Old 12-17-2020, 06:08 PM
  #8  
Platinum Member
Platinum Member
iTrader: (4)
 
endeavour32's Avatar
 
Join Date: May 2009
Location: Chicago, IL; Onekama, MI
Posts: 3,834
Received 79 Likes on 42 Posts
Default

I just measured my ITS shaft. It is the same as what you have pictured. 18" from middle of the u-joint to the end of the splines. So anyone looking, it is an ITS assembly.
endeavour32 is offline  
Old 12-17-2020, 06:32 PM
  #9  
253
Platinum Member
Platinum Member
Thread Starter
 
Join Date: Jan 2002
Location: Southern, IL.
Posts: 605
Received 12 Likes on 7 Posts
Default

Thanks Endeavour32 for the help to identify this shaft.
253 is offline  
Old 12-29-2020, 10:12 AM
  #10  
253
Platinum Member
Platinum Member
Thread Starter
 
Join Date: Jan 2002
Location: Southern, IL.
Posts: 605
Received 12 Likes on 7 Posts
Default

If anyone can use this, ITS, input shaft with XR yoke make me a decent offer as I will not need this.
Thanks
253 is offline  

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.