New mercury & gil engine mounts
 

The front pedestal mounts and zinc chromate aluminum gussets are used, but the engine mounts and rear cast iron gusset mounts are brand new never installed and are bagged up.
https://cimg7.ibsrv.net/gimg/www.off...ac927a1950.jpg
Gil 496 mounts for twins.
https://cimg9.ibsrv.net/gimg/www.off...41a2a451a1.jpg
The idea was to have the ears welded on to convert both mounts to single engine (The cast iron rear gussets bolt to either a borg warner transmission or a bravo driveline bearing housing) all hardware to bolt them up is pictured, new and mercury bags.
https://cimg1.ibsrv.net/gimg/www.off...ae65d041d5.jpg
So they could be used as either a single engine transmission driveline or bravo driveline set up. (The front stamped block mounts are used)
https://cimg2.ibsrv.net/gimg/www.off...f6173e81d9.jpg
The idea is that 4 big nuts and the engine comes out without crawling under there and unbolting the typical plates off vertical angles that are bolted to the stringers
https://cimg5.ibsrv.net/gimg/www.off...f3550fde03.jpg
In bags, clean and new. Like to sell both 496 mounts and the mercury rear gussets, and front block pad mounts for 350 plus shipping
https://cimg1.ibsrv.net/gimg/www.off...0f4b43916b.jpg
https://cimg3.ibsrv.net/gimg/www.off...6652f4af38.jpg
https://cimg8.ibsrv.net/gimg/www.off...74b7162210.jpg
These are front and rear aluminum gussets for pedestal mounts ( TRS 30 scarab) in perfect condition, sanblasted zinc chromated and boxed up years ago. Could be used for twin bravo front mounts too.
https://cimg6.ibsrv.net/gimg/www.off...959a15877c.jpg
Not sure what these are worth, virtually pricesless tho !
https://cimg8.ibsrv.net/gimg/www.off...8d3e68e93e.jpg
https://cimg9.ibsrv.net/gimg/www.off...918a7a7b85.jpg
Brand new NLA mercury single engine front mount never used. Paid 300 plus shipping, take 300 plus shipping.
https://cimg0.ibsrv.net/gimg/www.off...b76d71d54d.jpg
https://cimg4.ibsrv.net/gimg/www.off...b41984b774.jpg
https://cimg6.ibsrv.net/gimg/www.off...6f59f77857.jpg
Super secret mercury alignment tool for bravo. It aligns the drive bellhousing with the gimble bearing. Slide it on the algnment tool shaft to verify alignment, use feeler gauges to make it 100% aligned the way the old TRS drives were done, think the speedmasters too.
https://cimg9.ibsrv.net/gimg/www.off...f37e118d95.jpg
Not a scratch on it, i'll have to look up the price.
https://cimg0.ibsrv.net/gimg/www.off...63811f4aa0.jpg
https://cimg2.ibsrv.net/gimg/www.off...4e4a825f72.jpg
https://cimg3.ibsrv.net/gimg/www.off...04223d08ed.jpg

the rear cast iron gusset mounts and the front pad mounts could be used with pedestals and horizontal aluminum angles bolted onto the stringers to fashion up your own rail mount for either a single engine driveline transmission or bravo boat as well

I have a guy ill send your way looking

Thanks mike.

I also have mercury service manual #39 all 7 books half the price of a new set plus shipping and i'll go half the price of new on the bravo alignment special tool plus shipping.
https://cimg3.ibsrv.net/gimg/www.off...df96eeb08d.jpg
https://cimg4.ibsrv.net/gimg/www.off...293681c71e.jpg

Fyi those 496 front mounts clear a 10 quart oil pan and they aren't 496 gen 7 specific, a 454 502 etc will bolt up to them.
the only difference between single and twin 496 mounts are the position of the mounting plates.

I would be interested in books.

Pm me your cell phone # and address. Thered boxed, just need to drop at usps and get paypal

https://cimg2.ibsrv.net/gimg/www.off...8a6b327e02.jpg
Let me throw this out.
Say you got a 4 or 5 speedmaster on a box or a bravo and a stellings box.

If your close to the transom and are running a short driveshaft, These mounts will allow an up/down adjustment to reduce u joint angle when moving the box from the middle to either the top or bottom holes.
(I'll measure and picture the amount of adjustability if anyone's interested) safe to say at least 1/2 inch in either direction from midpoint. That amount could keep the the ujoints happy and intact.

New member and can’t send pm’s yet. Please shoot me a text or call and will forward my contact info. Chris 314-707-9215

Bravo books sold & shipped.
solid guy no trepadation selling to or buying from imo. Paypal'd me within minutes of getting off the phone and before i could get out of the house to the post office. (Tracking # and shipping label pictures sent)

Also he sent me some pics, you guys are gonna wanna see his restoration project, nice clean work on a very classic hull.
He just needs to get his post count up and get a thread going in the restoration section

how much for the aluminum gussets?