|
makes sense; I still have the same truck intake but F body oil pan for clearance. I left the engine stock because every cam out there made more tq and hp above 3500 and lost some below. being a 5000 lb 1960 Caddy I opted to keep the low end power as I will rarely be above 3500
|
If I keep the truck when its done I'll build a 6.2 hot rod but it will probably go through a Mecum auction where they bring good money
|
yea, some of those are bringing stupid money at auction. my caddy is going to be a mostly daily driver for me. I have a 1970 Olds Cutlass SX convertible that is one of about 730 built. last year one went thru BJ auction for over $100k. I have had it since 1983 and paid $750 for it. who would have guessed.
|
Keeping it all Chevy no 9 inch........installed a new 8.875 posi unit with 3.73 gears and new Richmond axles in the 12 bolt, truck will be light should be fine with the 4L60E trans.
|
|
Awesome job!!! Can't wait to see the finished project. I'm getting ready to do a LS swap in my 70 Chevelle. Just received the engine, trans and all of the goodies from GM. LS7 427/570 HP and a 4L75E trans, computers, etc.... . Really excited about this one. It's gonna be cool!
https://cimg9.ibsrv.net/gimg/www.off...0e63637e6d.jpg |
Originally Posted by OldSchool
(Post 4845865)
Awesome job!!! Can't wait to see the finished project. I'm getting ready to do a LS swap in my 70 Chevelle. Just received the engine, trans and all of the goodies from GM. LS7 427/570 HP and a 4L75E trans, computers, etc.... . Really excited about this one. It's gonna be cool!
https://cimg9.ibsrv.net/gimg/www.off...0e63637e6d.jpg https://cimg0.ibsrv.net/gimg/www.off...e9515e7583.jpg |
Nothing in my drivetrain is numbers matching, so that made it an easier decision!
|
I love the 70 Chevelle, had one myself in high school. Great looking example of one, love the functioning cowl induction. Did you do one of the GM's connect and cruise packages?
Originally Posted by OldSchool
(Post 4845865)
Awesome job!!! Can't wait to see the finished project. I'm getting ready to do a LS swap in my 70 Chevelle. Just received the engine, trans and all of the goodies from GM. LS7 427/570 HP and a 4L75E trans, computers, etc.... . Really excited about this one. It's gonna be cool!
https://cimg9.ibsrv.net/gimg/www.off...0e63637e6d.jpg |
Originally Posted by Wildman_grafix
(Post 4845928)
Did you do one of the GM's connect and cruise packages?
https://cimg2.ibsrv.net/gimg/www.off...c40b8d1f19.jpg https://cimg6.ibsrv.net/gimg/www.off...78956c8ae5.jpg https://cimg8.ibsrv.net/gimg/www.off...c87b06601f.jpg |
All good OldSchool I don't mind
|
https://cimg8.ibsrv.net/gimg/www.off...9e9876d08b.jpg
bit of a mock up of the relocation brackets, AC upper left and Alt and PS on the right https://cimg4.ibsrv.net/gimg/www.off...bc1f19e865.jpg |
https://cimg5.ibsrv.net/gimg/www.off...5020b284f6.jpg
https://cimg8.ibsrv.net/gimg/www.off...82ce4ead9f.jpg https://cimg0.ibsrv.net/gimg/www.off...02d83bb67d.jpg Some progress, took the cab to Tx friend of my brother in-law is doing the repair and get it ready for paint, think Im going to do flush glass on the windshield and rear. |
|
What brand radiator is that?
|
Originally Posted by OldSchool
(Post 4854478)
What brand radiator is that?
|
cab is blasted most of the metal work is done hope to be in primer in a couple weeks, then color in the jambs, firewall and interior
https://cimg3.ibsrv.net/gimg/www.off...bd06e8a186.jpg https://cimg4.ibsrv.net/gimg/www.off...15aa5535ea.jpg |
|
this is just a question as I have dealt with those calipers quite a bit. did you adjust them before putting the arm for the e-brake on? also if this is an automatic make sure you use the e-brake regularly with that setup as they will not self adjust if you dont and the ratchet in them will stick and you wont have rear brakes. if you already know about all that then you are ahead of most who use them. truck looks like it is coming along nice. I finally drove my 60 caddy LS swap. few things left to do but for a stock 5.3 it runs pretty nice.
|
Originally Posted by F-2 Speedy
(Post 4845502)
TIA Speedy |
Looks like this intake although fuggly it performs pretty well
LS Truck Intake Dyno Shootout (motortrend.com) |
this is coming along nicely
|
Love this thing going to be sweet
|
Originally Posted by F-2 Speedy
(Post 4860261)
Looks like this intake although fuggly it performs pretty well
LS Truck Intake Dyno Shootout (motortrend.com) |
Holy smokes Wally Id rather pull the engines in my boat.........:lolhit:
|
If it wasn't so expensive to switch over I'd go with a Holley carb manifold and Sniper EFI setup.
|
I need some help from the LS folks can I change coil packs to the LS3, 5, 7 on this build will the plug and play with the 5.3 truck wiring harness, all the cool V covers are for these coils
https://cimg4.ibsrv.net/gimg/www.off...0e669263b0.jpg |
F2, are you on LS1tech forums?
If not might want to join. I'd guess lots of knowledgeable guys over there have been through all the same issues you're at hundreds of times. |
good idea cheech, just joined
|
Originally Posted by F-2 Speedy
(Post 4861921)
good idea cheech, just joined
|
Originally Posted by cheech
(Post 4861916)
F2, are you on LS1tech forums?
If not might want to join. I'd guess lots of knowledgeable guys over there have been through all the same issues you're at hundreds of times. |
Originally Posted by F-2 Speedy
(Post 4862595)
not a single reply..........:lolhit:
Maybe your newbie credentials on there are handicapping you. Did you even get some derogatory replies telling you to search? |
Originally Posted by cheech
(Post 4862597)
That's a shame.
Maybe your newbie credentials on there are handicapping you. Did you even get some derogatory replies telling you to search? |
|
had to fab some upper shock relocation brackets
https://cimg5.ibsrv.net/gimg/www.off...5518c25ac4.jpg https://cimg9.ibsrv.net/gimg/www.off...397de569a3.jpg |
Incredible job!!! I sure have enjoyed following this thread! We finished my Chevelle and I'm lovin it! Weather permitting, I'm gonna drive it from here in Florida up to Maryland in May for a friend's car show. Good times!
Craig |
Wow sounds awesome, is that your short bed ?.........heading to TX in a couple weeks the cab and fenders are suppose to be in color
|
Originally Posted by F-2 Speedy
(Post 4864267)
Wow sounds awesome, is that your short bed ?.........heading to TX in a couple weeks the cab and fenders are suppose to be in color
My car runs better than I expected! :party-smiley-048::party-smiley-048: |
OldSchool, love the connect and cruise swap! I had a 70 SS in high school and college.
I never seen one with a bench seat?
Originally Posted by OldSchool
(Post 4864266)
Incredible job!!! I sure have enjoyed following this thread! We finished my Chevelle and I'm lovin it! Weather permitting, I'm gonna drive it from here in Florida up to Maryland in May for a friend's car show. Good times!
Craig 1970 Chevelle LS427 startup - YouTube |
|
| All times are GMT -5. The time now is 01:13 PM. |
Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.