700SCi 37AT
#1
Registered
Thread Starter
700SCi 37AT
Mark still has time to upgrade to these!
Originally Posted by Tony Montana
Dam that biatch is looking good. An inch of clear all that weight might slow it down
#3
Registered
Thread Starter
Re: my bimmer boyz.....
Originally Posted by Sydwayz
Scoops or a hatch like RadioActive and ThunderStorm?
Your opinion?
Last edited by Sydwayz; 12-28-2006 at 07:20 PM.
#4
Platinum Member
Platinum Member
Re: my bimmer boyz.....
Hatch for function. Scoops are good for race but cumbersome for pleasure especially if you like the ladies!!!
Last edited by crb76; 12-27-2006 at 08:06 PM.
#5
Registered
Join Date: Jan 2006
Location: Syracuse N.Y.
Posts: 4,951
Likes: 0
Received 0 Likes
on
0 Posts
Re: my bimmer boyz.....
no scoops. A hatch would make it more of a sleeper, The scoops would give it away. Can you just raise the hatch a little? Then figue a way to pipe air to them from the sides. P.S. when we going to see paint on that one,and where is it going?????
Last edited by cosmic12; 12-27-2006 at 07:59 PM.
#6
Re: my bimmer boyz.....
Originally Posted by ActiveThunder
You noticed that....
Your opinion?
Your opinion?
Tough call. I guess it depends on what the owner wants to do with the boat for the majority of the time.
I like both 'looks' that you have done so far; in the attached pics.
#7
Registered
Re: my bimmer boyz.....
Originally Posted by Sydwayz
Scoops or a hatch like RadioActive and ThunderStorm?
Last edited by Sydwayz; 12-28-2006 at 07:20 PM.
#8
AKA NoMoBoatin
Platinum Member
Join Date: Jan 2003
Location: Can't remember.
Posts: 3,684
Likes: 0
Received 0 Likes
on
0 Posts
Re: my bimmer boyz.....
Those bolt ons are alot higher than mine.I like the raised hatch instead of the scoops=less transom candy on the sun pad.
#9
Re: my bimmer boyz.....
Is the 700 boat going to have a bolt on swim platform? I like the raised center hatch like the 675KE boats had, but the whole sunpad is hardly usable for all day rafting and relaxing. I know plenty of folks that make do with the scoops like the 720T boat for an all-day cockpit/rafting experience.
If it were my boat, I would go toward a hybrid effect. My suggestion would be to start a second level of the sunpad at the point where you already put in the seam and the main cross support. At this point, it is laid up fiberglass all the way to the back of the hatch, and it slopes off with a curve toward the transom and swim platform. The entire front of the second level would be vertical, or somewhat beveled down toward the cockpit/backseat, and in this front "face" there would be air intakes for the bigger motors.
Basically it would be a vinyl sunpad built over scoops, that would follow a natural curve down to the back of the boat, and it would be all covered in vinyl, and strong enough that you don't have to puss yfoot around. Unfortunately, its going to add some weight, but the RadioActive type hatch, while functional and pretty, looks a bit delicate, and throws off some of the sharp lines.
You asked.
Rich, do you have any pics of the custom hatch work on Don & Geri's boat? That's another idea.
If it were my boat, I would go toward a hybrid effect. My suggestion would be to start a second level of the sunpad at the point where you already put in the seam and the main cross support. At this point, it is laid up fiberglass all the way to the back of the hatch, and it slopes off with a curve toward the transom and swim platform. The entire front of the second level would be vertical, or somewhat beveled down toward the cockpit/backseat, and in this front "face" there would be air intakes for the bigger motors.
Basically it would be a vinyl sunpad built over scoops, that would follow a natural curve down to the back of the boat, and it would be all covered in vinyl, and strong enough that you don't have to puss yfoot around. Unfortunately, its going to add some weight, but the RadioActive type hatch, while functional and pretty, looks a bit delicate, and throws off some of the sharp lines.
You asked.
Rich, do you have any pics of the custom hatch work on Don & Geri's boat? That's another idea.
Last edited by Sydwayz; 12-27-2006 at 08:20 PM.
#10
Registered
Join Date: Dec 2003
Posts: 105
Likes: 0
Received 0 Likes
on
0 Posts
Re: my bimmer boyz.....
Originally Posted by docmanrich37
A inch of clear great guess there won't be enough left to do my boat this week, unless you recycled my old clear. Pat great job on OverActive.Can't wait to see it in a couple weeks.
That's what happened last time, they, didn't get enough clear on it to make it stick good...