Extreme Measures... Make Over Edition

Reply Subscribe

Thread Tools

09-18-2022 | 10:41 AM

#121

kreed

Registered

Joined: Feb 2008

Posts: 6,755

Likes: 152

From: Connecticut

You are a brave man taking it to a run for its first time out! Id have been stressed out! LOL...boat looks beautiful. love the new dash set up.

02-04-2023 | 11:58 AM

#122

Rookie

Thread Starter

Registered

Joined: Jan 2003

Posts: 6,018

Likes: 1,521

From: Grand Rapids, MI

Finished my digital dash up a few weeks ago. Talked to my upholsterer the other day and he will do my bolsters and other cushions early spring after my Mustang interior.
.

02-04-2023 | 12:59 PM

#123

TomZ

Platinum Member

Joined: Feb 2001

Posts: 4,295

Likes: 1,457

From: Virginia Beach

That’s pretty sweet!!

Are your switches for 3/4-inch holes?

Last edited by TomZ; 02-05-2023 at 07:34 PM.

02-04-2023 | 07:19 PM

#124

Rookie

Thread Starter

Registered

Joined: Jan 2003

Posts: 6,018

Likes: 1,521

From: Grand Rapids, MI

Quote:

Originally Posted by TomZ

That pretty sweet!!

Are your switches for 3/4-inch holes?

Pretty much. They are 19mm (0.748") switches. I drew the letters and layout in CAD and then laser cut the holes and laser engraved the the lettering.

02-05-2023 | 07:35 PM

#125

TomZ

Platinum Member

Joined: Feb 2001

Posts: 4,295

Likes: 1,457

From: Virginia Beach

Did you do all the engraving and cutting yourself?

02-05-2023 | 08:08 PM

#126

Rookie

Thread Starter

Registered

Joined: Jan 2003

Posts: 6,018

Likes: 1,521

From: Grand Rapids, MI

Quote:

Originally Posted by TomZ

Did you do all the engraving and cutting yourself?

I had a friend at work cut and engrave the dash for me. I did not have my laser at the time. After I got it back I purchased a laser the next week. Hers is a CO2 laser and mine is only a diode laser. Mine will engrave white acrylic, but has trouble cutting through white. Black, blue green, gray and others is not a problem for me to cut through.

Also, the switches are either momentary or latched dependent on what they are turning on/off. Also, the ignition are higher amperage switches.

Last edited by Rookie; 02-05-2023 at 11:29 PM.

02-06-2023 | 12:38 PM

#127

TexomaPowerboater

Registered

Joined: Jan 2007

Posts: 6,474

Likes: 358

From: Mansfield, TX

Quote:

Originally Posted by Rookie

Finished up the majority of the back of the transom. New stainless drain plugs and yes, the lag screw does go to the trim tab mounts. It mounts directly behind the stringer so a thru bolt can't be use. Also installed 2 new Rule 1100 27SA bilge pumps. Don't know how I feel about them. They do not use a float switch. They use Rule "Smart Technology" and power on every 2.5 minutes and sense for resistance. Also cutout new high temp silicone exhaust seals.
https://www.westmarine.com/buy/rule-...06?recordNum=5

Where did you get those stainless exhaust rings? I have not been able to source one with four holes, they all seem to have three and my original ones were four.

02-06-2023 | 12:43 PM

#128

DrFeelgood

Registered

Joined: Aug 2007

Posts: 1,422

Likes: 1,062

From: Orlando, FL

Quote:

Originally Posted by TexomaPowerboater

Where did you get those stainless exhaust rings? I have not been able to source one with four holes, they all seem to have three and my original ones were four.

https://www.stainlessmarine.com/shop...-4-od-pipe-ea/