28ss resto moving along
#21
Bolsters
Barry
__________________
Thanks, Barry
Driver - High's Fuel Your Journey Cigarette Racing Team #598
Thanks, Barry
Driver - High's Fuel Your Journey Cigarette Racing Team #598
Last edited by O.C.Barry; 08-20-2007 at 07:35 AM. Reason: spelling
#22
Registered
Thread Starter
Join Date: Dec 2006
Location: toms river nj
Posts: 56
Likes: 0
Received 0 Likes
on
0 Posts
OC Barry,
my e-mail is [email protected] or [email protected]
the stands are no problem.
thanks,
Chris
my e-mail is [email protected] or [email protected]
the stands are no problem.
thanks,
Chris
#23
Registered
Platinum Member
Hey Barry,
Nice to hear you're doing a 28! Is it/was it brown??
What power and drives?
I am basically on my 5th TRS drive(combination of #4's good upper, and #3's good lower) since 2003. I may finally go to a Konrad this winter, and may have a total of three drives available, (one good, two with blown lowers), along with gimble if you need anything.
I also have a 177 blower available, sitting on bench, as I have been NA since 2004.
Eddy
Nice to hear you're doing a 28! Is it/was it brown??
What power and drives?
I am basically on my 5th TRS drive(combination of #4's good upper, and #3's good lower) since 2003. I may finally go to a Konrad this winter, and may have a total of three drives available, (one good, two with blown lowers), along with gimble if you need anything.
I also have a 177 blower available, sitting on bench, as I have been NA since 2004.
Eddy
#24
Registered
Thread Starter
Join Date: Dec 2006
Location: toms river nj
Posts: 56
Likes: 0
Received 0 Likes
on
0 Posts
pics of the engines
These engines were supposed to get Dart 200cc heads. when they got to the engine builder he inspected them and found that 3 of the 4 had factory repairs. Dart wouldnt replace them or gaurantee the repairs and he ended up sending them all back. these engines are getting RHS heads.
Chris
Chris
#25
Registered
Nice looking rig. IMO the boat looked great from the factory. I would have done the same keeping it original in appearance. I have a Tbred that looks great with factory graphics. Can't wait to see it in running in the water.Best of luck Bob.
#26
Hey Barry,
Nice to hear you're doing a 28! Is it/was it brown??
What power and drives?
I am basically on my 5th TRS drive(combination of #4's good upper, and #3's good lower) since 2003. I may finally go to a Konrad this winter, and may have a total of three drives available, (one good, two with blown lowers), along with gimble if you need anything.
I also have a 177 blower available, sitting on bench, as I have been NA since 2004.
Eddy
Nice to hear you're doing a 28! Is it/was it brown??
What power and drives?
I am basically on my 5th TRS drive(combination of #4's good upper, and #3's good lower) since 2003. I may finally go to a Konrad this winter, and may have a total of three drives available, (one good, two with blown lowers), along with gimble if you need anything.
I also have a 177 blower available, sitting on bench, as I have been NA since 2004.
Eddy
No, the boat has a black hull. I am installing new Bravo XR transom assemblies and new IMCO platinum XR's. Blown 355 Cubic inch small blocks (.0404 over) with WP heads, WISECO pistons, and Jesel rocker assemblies. We are building the boat for P4, so it should be a interesting ride.
My engine builder has a pair of good SSM4's if you are interested.
Send me your e-mail address and we'll talk off line about the 177 blower, I am interested.
Good to hear from you again, Barry
__________________
Thanks, Barry
Driver - High's Fuel Your Journey Cigarette Racing Team #598
Thanks, Barry
Driver - High's Fuel Your Journey Cigarette Racing Team #598
#27
Registered
Platinum Member
Eddy - Please refresh my memory, your 27 Cigarette is my old boat, correct (the one I sold to Kenny Boss)? Yes. I'm apparently going through a cycle of offshore boats in this order: 28 Cigarette, 27 Cigarette, 34 Coyote; 38 Cigarette, 20 Cigarette (still have it), and now 28 Cigarette.
No, the boat has a black hull. I am installing new Bravo XR transom assemblies and new IMCO platinum XR's. Blown 355 Cubic inch small blocks (.0404 over) with WP heads, WISECO pistons, and Jesel rocker assemblies. We are building the boat for P4, so it should be a interesting ride.
My engine builder has a pair of good SSM4's if you are interested.
Send me your e-mail address and we'll talk off line about the 177 blower, I am interested.
Good to hear from you again, Barry
No, the boat has a black hull. I am installing new Bravo XR transom assemblies and new IMCO platinum XR's. Blown 355 Cubic inch small blocks (.0404 over) with WP heads, WISECO pistons, and Jesel rocker assemblies. We are building the boat for P4, so it should be a interesting ride.
My engine builder has a pair of good SSM4's if you are interested.
Send me your e-mail address and we'll talk off line about the 177 blower, I am interested.
Good to hear from you again, Barry
Any idea where I might get a set of the 56" SS side vents made??
I'll try to PM you.
#28
Registered
Platinum Member
Thread
Thread Starter
Forum
Replies
Last Post
THRILLSEEKER
General Boating Discussion
4
10-11-2002 08:29 AM