# dyno #s sbc
#1
Registered
Thread Starter
Join Date: Dec 2009
Location: Perry FL
Posts: 75
Likes: 0
Received 0 Likes
on
0 Posts
# dyno #s sbc
Any guessers out there.
Dart shp block 385 cid
Eagle 3.75 forged crank,& 6" rods w/their esp treatment
-16 Srp slugs fitted w/Mahle rings.
Clevite
Madara (rm builder ) stick
lsa 112, 6.9 overlap, 1.5 ratio, duration I=228 E=234 lift
.5553 .53415
Morel retro
Manley pushrods
AFR 195 aluminum milled to 70cc
Scorpion 1.5 rockers
Rpm air gap
Pro Systems carb
Msd ignition
all Arp fasteners
Dart shp block 385 cid
Eagle 3.75 forged crank,& 6" rods w/their esp treatment
-16 Srp slugs fitted w/Mahle rings.
Clevite
Madara (rm builder ) stick
lsa 112, 6.9 overlap, 1.5 ratio, duration I=228 E=234 lift
.5553 .53415
Morel retro
Manley pushrods
AFR 195 aluminum milled to 70cc
Scorpion 1.5 rockers
Rpm air gap
Pro Systems carb
Msd ignition
all Arp fasteners
#3
Registered
Any guessers out there.
Dart shp block 385 cid
Eagle 3.75 forged crank,& 6" rods w/their esp treatment
-16 Srp slugs fitted w/Mahle rings.
Clevite
Madara (rm builder ) stick
lsa 112, 6.9 overlap, 1.5 ratio, duration I=228 E=234 lift
.5553 .53415
Morel retro
Manley pushrods
AFR 195 aluminum milled to 70cc
Scorpion 1.5 rockers
Rpm air gap
Pro Systems carb
Msd ignition
all Arp fasteners
Dart shp block 385 cid
Eagle 3.75 forged crank,& 6" rods w/their esp treatment
-16 Srp slugs fitted w/Mahle rings.
Clevite
Madara (rm builder ) stick
lsa 112, 6.9 overlap, 1.5 ratio, duration I=228 E=234 lift
.5553 .53415
Morel retro
Manley pushrods
AFR 195 aluminum milled to 70cc
Scorpion 1.5 rockers
Rpm air gap
Pro Systems carb
Msd ignition
all Arp fasteners
#5
Registered
iTrader: (1)
I would say 480 lb/ft @ 4500 RPM and 470hp@ 5500RPM. These are through the dyno headers. I would expect one of Bob's cams to hold the hp within 2 for about 4-500 RPM. My 383 was very similar with Bobs cam in it and a set of ported trick flows, I was running a single plane though.
#7
Registered
Thread Starter
Join Date: Dec 2009
Location: Perry FL
Posts: 75
Likes: 0
Received 0 Likes
on
0 Posts
sbc #s
462h 459t
Incorrect metering blocks out of the box. Patrick to ship new ones ASAP. don't know if I'll pull again.
This engine replaces a 1988 350 mag 250-270h 300-325t.
Going in a 5000# bow rider.
Mr Gadgets building me a BADD AZZ B 1 . Thanks for the intrest.
Lots more of this story to follow.
P.T.L.
Rory
Incorrect metering blocks out of the box. Patrick to ship new ones ASAP. don't know if I'll pull again.
This engine replaces a 1988 350 mag 250-270h 300-325t.
Going in a 5000# bow rider.
Mr Gadgets building me a BADD AZZ B 1 . Thanks for the intrest.
Lots more of this story to follow.
P.T.L.
Rory