Go Back  Offshoreonly.com > Technical > Drives and Lower Units
Wanted:  1991 Bravo 1 Clutches >

Wanted: 1991 Bravo 1 Clutches

Notices

Wanted: 1991 Bravo 1 Clutches

Thread Tools
 
Old 07-28-2009 | 05:41 PM
  #1  
NOMO's Avatar
Thread Starter
VIP Member
 
Joined: Nov 2008
Posts: 106
Likes: 0
From: LOTO/Weldon Spring, MO
Default Wanted: 1991 Bravo 1 Clutches

I am looking to locate clutches for twin 1991 Bravo 1 drives new or most likely used in good condition. I was told that I would need a entire gear set because the clutch for my model is no longer made and you need to replace the entire upper gear set. So does any one know where I might find clutches for my 1991 Bravo 1's??

Thanks
NOMO is offline  
Reply
Old 07-29-2009 | 07:55 AM
  #2  
Registered
 
Joined: Feb 2004
Posts: 448
Likes: 4
From: Camden, NC 27921
Default

Is a 1993 upper gear set the same? If so I can help you.
Harvey is offline  
Reply
Old 07-29-2009 | 07:58 AM
  #3  
NOMO's Avatar
Thread Starter
VIP Member
 
Joined: Nov 2008
Posts: 106
Likes: 0
From: LOTO/Weldon Spring, MO
Default

Originally Posted by Harvey
Is a 1993 upper gear set the same? If so I can help you.
I am not sure when they changed the setup, I will try to find out.
NOMO is offline  
Reply
Old 07-29-2009 | 08:21 PM
  #4  
Mr Gadgets's Avatar
Charter Member #601
 
Joined: Dec 2000
Posts: 3,276
Likes: 5
From: Holland, Mi USA.
Default

The 93 should be the same as the 91. I think they made the change around 2000 or so. Each of you measure the height of the cone and that will tell you. The newer ones are shorter because the floor of the newer gears are thicker.
The earlier drives, 88-89 have a different shift fork also. If you compare them you can tell if you have the same items and Havey can help you.. My guess is they are the same.

Hope this helps
Dick
Mr Gadgets is offline  
Reply
Old 07-29-2009 | 08:55 PM
  #5  
NOMO's Avatar
Thread Starter
VIP Member
 
Joined: Nov 2008
Posts: 106
Likes: 0
From: LOTO/Weldon Spring, MO
Default

Originally Posted by Harvey
Is a 1993 upper gear set the same? If so I can help you.
Do you have the entire gear set or just clutches? Also if you have the full set what ratio?

Thanks
NOMO is offline  
Reply
Old 07-30-2009 | 12:02 AM
  #6  
Registered
 
Joined: Jul 2009
Posts: 9
Likes: 0
Default

Upgrade to a newer clutch. You will need the newer shift fork as well. The shifting will improve as well. For better results install Merc s new drive cable. Shift with 2 fingers
NordicSS is offline  
Reply
Old 07-30-2009 | 12:04 AM
  #7  
Registered
 
Joined: Jul 2009
Posts: 9
Likes: 0
Default

Shift forks changed to newest style around 1997. I have 2 sets
NordicSS is offline  
Reply
Old 07-30-2009 | 11:25 AM
  #8  
Registered
 
Joined: Feb 2004
Posts: 448
Likes: 4
From: Camden, NC 27921
Default

I have the full set, they are 1.5 to 1. Ialso have the shift fort. Give me a call 252-339-4560. It's easier to explain all I have.
Harvey is offline  
Reply
Old 07-30-2009 | 02:42 PM
  #9  
Mindi
 
Joined: Jan 2005
Posts: 313
Likes: 0
From: Hollywood, FL
Default

Hello we have 3 good used ones in stock call Doller offshore at 954-237-0332 Julio
Doller Offshore is offline  
Reply
Old 07-30-2009 | 05:28 PM
  #10  
PAST DUE's Avatar
Registered
 
Joined: Jul 2009
Posts: 173
Likes: 0
From: GILBERT, S.C.
Default

2 used ones here low hours complete set 1;65 ration but will part out if needed p.m. me for more iinfo
PAST DUE is offline  
Reply


Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.