Extension boxes and blackhawks
11-18-2018 | 05:01 PM
#11
Registered
Joined: Jan 2002
Posts: 4,612
Likes: 7
From: ALTO, MI
I would set it at the height that will make the drive bullet sit on top of the water coming off the bottom at speed.
my Daytona is set up this way at +2 inches using a -3 IMCO shortie and an IMCO neutral ext. box.
At speed the water coming under the boat goes under the gear case bullet.
I even had to lower the water pick up to just in front of the skag.
I also cut the bell off the back of my prop. This made a noticeable drop in the stern.
and I agree that the closer the gear case gets to the surface the more it wants to surface causing a bow down attitude.
my Daytona is set up this way at +2 inches using a -3 IMCO shortie and an IMCO neutral ext. box.
At speed the water coming under the boat goes under the gear case bullet.
I even had to lower the water pick up to just in front of the skag.
I also cut the bell off the back of my prop. This made a noticeable drop in the stern.
and I agree that the closer the gear case gets to the surface the more it wants to surface causing a bow down attitude.
Last edited by Tinkerer; 11-18-2018 at 05:03 PM.
11-18-2018 | 05:19 PM
#12
Registered
Joined: May 2009
Posts: 1,941
Likes: 526
Page 21 post 206 (adjustable extension box pics)
40' Outlaw Upgrades - Twin 900Sc to 1000hp Duramax Diesels
Guessing you know that the stelling boxes are adjustable up and down so the perfect drive height can be acheived,
Also they are nla.
No reason imco boxes couldnt be modified to accept the rear hangar for a driveline and no reason the boxes couldnt
be mounted on custom plates/short boxes that would allow for the boxes to be adjusted up or down a few inches
The extra weight of those parts would help balance, plus the mercury driveline still uses the rubber coupler
Unlike the stellings so no extra abuse on the drive.
More money to go custom and adjustable on the front end of this build rather than nasa level math for a one shot
Hope its right x dimension and with no spacers have to recut and rebuild an inch in either direction later
40' Outlaw Upgrades - Twin 900Sc to 1000hp Duramax Diesels
Guessing you know that the stelling boxes are adjustable up and down so the perfect drive height can be acheived,
Also they are nla.
No reason imco boxes couldnt be modified to accept the rear hangar for a driveline and no reason the boxes couldnt
be mounted on custom plates/short boxes that would allow for the boxes to be adjusted up or down a few inches
The extra weight of those parts would help balance, plus the mercury driveline still uses the rubber coupler
Unlike the stellings so no extra abuse on the drive.
More money to go custom and adjustable on the front end of this build rather than nasa level math for a one shot
Hope its right x dimension and with no spacers have to recut and rebuild an inch in either direction later
11-19-2018 | 12:08 PM
#15
Registered
Joined: Oct 2007
Posts: 728
Likes: 4
From: uithoorn,the netherlands
I have done a lot of research on the blackhawks amd
they run best when bullet is out of the water so You want to go higher as your now even whig the bottom
problem whit this is that You have less leverage to Carry the bow but the black hawk is not designed to Carry the bow
the hull need to have natural bow lift build in so might check if your hull has decent rocker in the bottom
they run best when bullet is out of the water so You want to go higher as your now even whig the bottom
problem whit this is that You have less leverage to Carry the bow but the black hawk is not designed to Carry the bow
the hull need to have natural bow lift build in so might check if your hull has decent rocker in the bottom
11-19-2018 | 12:57 PM
#16
Thread Starter
Registered
Joined: Jul 2017
Posts: 32
Likes: 0
From: Harrington DE
I have done a lot of research on the blackhawks amd
they run best when bullet is out of the water so You want to go higher as your now even whig the bottom
problem whit this is that You have less leverage to Carry the bow but the black hawk is not designed to Carry the bow
the hull need to have natural bow lift build in so might check if your hull has decent rocker in the bottom
they run best when bullet is out of the water so You want to go higher as your now even whig the bottom
problem whit this is that You have less leverage to Carry the bow but the black hawk is not designed to Carry the bow
the hull need to have natural bow lift build in so might check if your hull has decent rocker in the bottom
11-19-2018 | 04:05 PM
#17
Offshoreonly Advertiser
Joined: Mar 2001
Posts: 2,517
Likes: 280
From: Pompano Beach FL, USA
Here is a drawing I made when I figured the X on my 20 Cigarette. Unfortunately I have not run it yet. But yes I think the gearcase needs to be above the bottom.
__________________
Marc
www.mercruiserparts.com
www.go-fast.com
www.bammarine.com
www.cyborgtransmissions.com
It's not alive -www.BoatStuffExpress.com - temporarily retired
Marc
www.mercruiserparts.com
www.go-fast.com
www.bammarine.com
www.cyborgtransmissions.com
It's not alive -www.BoatStuffExpress.com - temporarily retired
11-19-2018 | 08:21 PM
#20
VIP Member
Joined: Feb 2004
Posts: 12,314
Likes: 1,556
From: Maryland
the question was about a box and the difference in the drive height and I answered it. every 12 inches you take a drive back lowers your X dim by an inch as well as changes the COG. of course props make a diff, i have multiple sets of 31s, 29's and sold my sets of 27s. the set on now was done by cutting edge and hit the 86 on its first run with minimal trim and less than 5k rpms, at 5800 it will be 100 plus.. I nailed the X dim perfectly.
