Notices
General Boating Discussion

Fastech 312 Problems

Thread Tools
 
Old 05-26-2015 | 01:07 PM
  #1  
Thread Starter
Registered
 
Joined: May 2015
Posts: 5
Likes: 0
Default Fastech 312 Problems

New on here heard it was a great site for powerboats. Have a 2000 formula fastech 312 with twin 454 mpi NOT the mag motors. have the factory 28 bravo one props on it and can get more then 3800 RPM 55 mph out of it. Anything i should look at that could be causing the low rpm. and is terrible getting on plan even with the k-planes all the way down. any help would be great thank you. new cap rotor and plugs this season.
Bmichels8587 is offline  
Reply
Old 05-26-2015 | 01:10 PM
  #2  
Sydwayz's Avatar
Forum Regulator
20 Year Member
Super Moderators
VIP Member
 
Joined: May 2001
Posts: 24,203
Likes: 1,592
From: Worldwide
Default

Did you just get the boat and are those the props it came with? Have you tried anything else? They seem a little steep for that boat and power.

Often sellers will chuck on any old props they have at the sale. They may not be your best choice.
Sydwayz is offline  
Reply
Old 05-26-2015 | 01:11 PM
  #3  
Thread Starter
Registered
 
Joined: May 2015
Posts: 5
Likes: 0
Default

They're the props from formula good friends with original owner. i ran 26s last year seemed better but still wasnt getting into the rpm range id like to run it.
Bmichels8587 is offline  
Reply
Old 05-26-2015 | 01:13 PM
  #4  
VoodooRob's Avatar
VIP Member
10 Year Member
VIP Member
 
Joined: Jul 2011
Posts: 1,992
Likes: 48
From: Cleveland Ohio
Default

Did you try calling Formula and getting the info for the correct factory installed props? That would get you a baseline.
VoodooRob is offline  
Reply
Old 05-26-2015 | 01:14 PM
  #5  
VoodooRob's Avatar
VIP Member
10 Year Member
VIP Member
 
Joined: Jul 2011
Posts: 1,992
Likes: 48
From: Cleveland Ohio
Default

Isn"t the 454 MPI 310 HP, rated at 3800-4200 RPM?
VoodooRob is offline  
Reply
Old 05-26-2015 | 01:16 PM
  #6  
Knot 4 Me's Avatar
Registered
20 Year Member
 
Joined: Jun 2005
Posts: 8,407
Likes: 797
From: Central IL
Default

Originally Posted by voodoorob
isn"t the 454 mpi 310 hp, rated at 3800-4200 rpm?
4,200 - 4,600 rpm.
Knot 4 Me is offline  
Reply
Old 05-26-2015 | 01:17 PM
  #7  
Thread Starter
Registered
 
Joined: May 2015
Posts: 5
Likes: 0
Default

think its more like 4600 the mag is even more. atleast this is what im told
Bmichels8587 is offline  
Reply
Old 05-26-2015 | 01:18 PM
  #8  
Thread Starter
Registered
 
Joined: May 2015
Posts: 5
Likes: 0
Default

with the 26s i can get 4000 maybe 4200. thinking about having them sharpened to get a little more rpm out of it. would that help?
Bmichels8587 is offline  
Reply
Old 05-26-2015 | 01:25 PM
  #9  
VoodooRob's Avatar
VIP Member
10 Year Member
VIP Member
 
Joined: Jul 2011
Posts: 1,992
Likes: 48
From: Cleveland Ohio
Default

Your right 4200-4600, I had that same engine a few boats ago and remembered wrong numbers. You may have the factory props but they could have been damaged or modified along the way, or replaced with a same numbered set that were worked over.
VoodooRob is offline  
Reply
Old 05-26-2015 | 01:25 PM
  #10  
Registered
 
Joined: Nov 2006
Posts: 1,261
Likes: 2
From: Great Sacandaga Lake, NY
Default

Originally Posted by Bmichels8587
with the 26s i can get 4000 maybe 4200. thinking about having them sharpened to get a little more rpm out of it. would that help?
Do you know anyone with a set of 24s to try?? How was the boat mid range with the 26s?
Rattlesnake Jake is offline  
Reply


Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.