Push-On hose for fuel plumbing?
05-21-2013 | 10:56 AM
#12
Banned
Joined: Mar 2002
Posts: 2,103
Likes: 3
From: michigan
These are the Oetiker stainless steel band clamps that I have found to work the best for the Telflex hose. We us # 16702498 or (16700022) for the 3/8 hose and # 16700026 for the 1/2 hose.
Last edited by brian41; 05-21-2013 at 11:14 AM.
05-21-2013 | 04:35 PM
#13
Registered
Joined: Nov 2005
Posts: 4,554
Likes: 3
From: Fredericksburg, Va
I would use clamps as well....used for all my oil lines, worked great..but one came off at block adapter...summit replaced all the hose, used aeroquip after the summit brand..but did clamp all !!!!
05-24-2015 | 05:27 PM
#14
Thread Starter
Registered
Joined: Jun 2012
Posts: 1,455
Likes: 1
From: OK CIty, OK
Bump. Thinking about using AQP socketless on my oil cooler/filter setup with a 212* thermostat. I shouldn't have any issue at that temp, correct?
Aeroquip hasn't been very timely with a reply to my question about its operating temp.
Aeroquip hasn't been very timely with a reply to my question about its operating temp.
05-24-2015 | 06:51 PM
#17
Registered
Joined: Jan 2006
Posts: 688
Likes: 0
From: wisconsin
[Code of Federal Regulations]
[Title 33, Volume 2]
[Revised as of July 1, 2001]
From the U.S. Government Printing Office via GPO Access
[CITE: 33CFR183.540]
[Page 780]
TITLE 33--NAVIGATION AND NAVIGABLE WATERS
CHAPTER I--COAST GUARD, DEPARTMENT OF TRANSPORTATION (CONTINUED)
PART 183--BOATS AND ASSOCIATED EQUIPMENT--Table of Contents
Subpart J--Fuel Systems
Sec. 183.540 Hoses: Standards and markings.
(a) ``USCG Type A1'' hose means hose that meets the performance
requirements of:
(1) SAE Standard J1527DEC85, Class 1 and the fire test in
Sec. 183.590; or
(2) Underwriters' Laboratories, Inc. (UL) Standard 1114.
(b) ``USCG Type A2'' hose means hose that meets the performance
requirements of SAE Standard J1527DEC85, Class 2 and the fire test in
Sec. 183.590;
(c) ``USCG Type B1'' hose means hose that meets the performance
requirements of SAE Standard J1527DEC85, Class 1.
(d) ``USCG Type B2'' hose means hose that meets the performance
requirements of SAE Standard J1527DEC85, Class 2.
Note: SAE Class 1 hose has a permeation rating of 100 grams or less
fuel loss per square meter of interior surface in 24 hours.
SAE Class 2 hose has a permeation rating of 300 grams or less fuel
loss per square meter of interior surface in 24 hours.
(e) Each ``USCG Type A1,'' ``USCG Type A2,'' ``USCG Type B1,'' and
``USCG Type B2'' hose must be identified by the manufacturer by a
marking on the hose.
(f) Each marking must contain the following information in English:
(1) The statement ``USCG TYPE (insert A1 or A2 or B1 or B2).''
(2) The year in which the hose was manufactured.
(3) The manufacturer's name or registered trademark.
(g) Each character must be block capital letters and numerals that
are at least one eighth-inch high.
(h) Each marking must be permanent, legible, and on the outside of
the hose at intervals of 12 inches or less.
[CGD 85-098, 52 FR 19728, May 27, 1987]
[Title 33, Volume 2]
[Revised as of July 1, 2001]
From the U.S. Government Printing Office via GPO Access
[CITE: 33CFR183.540]
[Page 780]
TITLE 33--NAVIGATION AND NAVIGABLE WATERS
CHAPTER I--COAST GUARD, DEPARTMENT OF TRANSPORTATION (CONTINUED)
PART 183--BOATS AND ASSOCIATED EQUIPMENT--Table of Contents
Subpart J--Fuel Systems
Sec. 183.540 Hoses: Standards and markings.
(a) ``USCG Type A1'' hose means hose that meets the performance
requirements of:
(1) SAE Standard J1527DEC85, Class 1 and the fire test in
Sec. 183.590; or
(2) Underwriters' Laboratories, Inc. (UL) Standard 1114.
(b) ``USCG Type A2'' hose means hose that meets the performance
requirements of SAE Standard J1527DEC85, Class 2 and the fire test in
Sec. 183.590;
(c) ``USCG Type B1'' hose means hose that meets the performance
requirements of SAE Standard J1527DEC85, Class 1.
(d) ``USCG Type B2'' hose means hose that meets the performance
requirements of SAE Standard J1527DEC85, Class 2.
Note: SAE Class 1 hose has a permeation rating of 100 grams or less
fuel loss per square meter of interior surface in 24 hours.
SAE Class 2 hose has a permeation rating of 300 grams or less fuel
loss per square meter of interior surface in 24 hours.
(e) Each ``USCG Type A1,'' ``USCG Type A2,'' ``USCG Type B1,'' and
``USCG Type B2'' hose must be identified by the manufacturer by a
marking on the hose.
(f) Each marking must contain the following information in English:
(1) The statement ``USCG TYPE (insert A1 or A2 or B1 or B2).''
(2) The year in which the hose was manufactured.
(3) The manufacturer's name or registered trademark.
(g) Each character must be block capital letters and numerals that
are at least one eighth-inch high.
(h) Each marking must be permanent, legible, and on the outside of
the hose at intervals of 12 inches or less.
[CGD 85-098, 52 FR 19728, May 27, 1987]
05-24-2015 | 07:28 PM
#18
Registered
Joined: Jan 2006
Posts: 3,601
Likes: 1,169
From: taxachusetts
[Code of Federal Regulations]
[Title 33, Volume 2]
[Revised as of July 1, 2001]
From the U.S. Government Printing Office via GPO Access
[CITE: 33CFR183.540]
[Page 780]
TITLE 33--NAVIGATION AND NAVIGABLE WATERS
CHAPTER I--COAST GUARD, DEPARTMENT OF TRANSPORTATION (CONTINUED)
PART 183--BOATS AND ASSOCIATED EQUIPMENT--Table of Contents
Subpart J--Fuel Systems
Sec. 183.540 Hoses: Standards and markings.
(a) ``USCG Type A1'' hose means hose that meets the performance
requirements of:
(1) SAE Standard J1527DEC85, Class 1 and the fire test in
Sec. 183.590; or
(2) Underwriters' Laboratories, Inc. (UL) Standard 1114.
(b) ``USCG Type A2'' hose means hose that meets the performance
requirements of SAE Standard J1527DEC85, Class 2 and the fire test in
Sec. 183.590;
(c) ``USCG Type B1'' hose means hose that meets the performance
requirements of SAE Standard J1527DEC85, Class 1.
(d) ``USCG Type B2'' hose means hose that meets the performance
requirements of SAE Standard J1527DEC85, Class 2.
Note: SAE Class 1 hose has a permeation rating of 100 grams or less
fuel loss per square meter of interior surface in 24 hours.
SAE Class 2 hose has a permeation rating of 300 grams or less fuel
loss per square meter of interior surface in 24 hours.
(e) Each ``USCG Type A1,'' ``USCG Type A2,'' ``USCG Type B1,'' and
``USCG Type B2'' hose must be identified by the manufacturer by a
marking on the hose.
(f) Each marking must contain the following information in English:
(1) The statement ``USCG TYPE (insert A1 or A2 or B1 or B2).''
(2) The year in which the hose was manufactured.
(3) The manufacturer's name or registered trademark.
(g) Each character must be block capital letters and numerals that
are at least one eighth-inch high.
(h) Each marking must be permanent, legible, and on the outside of
the hose at intervals of 12 inches or less.
[CGD 85-098, 52 FR 19728, May 27, 1987]
[Title 33, Volume 2]
[Revised as of July 1, 2001]
From the U.S. Government Printing Office via GPO Access
[CITE: 33CFR183.540]
[Page 780]
TITLE 33--NAVIGATION AND NAVIGABLE WATERS
CHAPTER I--COAST GUARD, DEPARTMENT OF TRANSPORTATION (CONTINUED)
PART 183--BOATS AND ASSOCIATED EQUIPMENT--Table of Contents
Subpart J--Fuel Systems
Sec. 183.540 Hoses: Standards and markings.
(a) ``USCG Type A1'' hose means hose that meets the performance
requirements of:
(1) SAE Standard J1527DEC85, Class 1 and the fire test in
Sec. 183.590; or
(2) Underwriters' Laboratories, Inc. (UL) Standard 1114.
(b) ``USCG Type A2'' hose means hose that meets the performance
requirements of SAE Standard J1527DEC85, Class 2 and the fire test in
Sec. 183.590;
(c) ``USCG Type B1'' hose means hose that meets the performance
requirements of SAE Standard J1527DEC85, Class 1.
(d) ``USCG Type B2'' hose means hose that meets the performance
requirements of SAE Standard J1527DEC85, Class 2.
Note: SAE Class 1 hose has a permeation rating of 100 grams or less
fuel loss per square meter of interior surface in 24 hours.
SAE Class 2 hose has a permeation rating of 300 grams or less fuel
loss per square meter of interior surface in 24 hours.
(e) Each ``USCG Type A1,'' ``USCG Type A2,'' ``USCG Type B1,'' and
``USCG Type B2'' hose must be identified by the manufacturer by a
marking on the hose.
(f) Each marking must contain the following information in English:
(1) The statement ``USCG TYPE (insert A1 or A2 or B1 or B2).''
(2) The year in which the hose was manufactured.
(3) The manufacturer's name or registered trademark.
(g) Each character must be block capital letters and numerals that
are at least one eighth-inch high.
(h) Each marking must be permanent, legible, and on the outside of
the hose at intervals of 12 inches or less.
[CGD 85-098, 52 FR 19728, May 27, 1987]
