Cam and valvetrain longevity....??? low duration high lift...
11-07-2016 | 11:42 AM
#1591
Platinum Member
Joined: Jul 2008
Posts: 931
Likes: 0
From: Little River SC
My ex used to tell me everything was my fault. So I thought about that and came up with a reply that used to drive her nuts....
Kathy: This is ALL YOUR FAULT
Me: Yes its all my fault, EVERYTHING is my fault!! I am fully responsible for ALL OF IT!! And since the only entity with that much responsibility is GOD, you need to get down on your knees and worship me NOW!!
(Disclaimer) This may be part of the reason she is my ex.....
Kathy: This is ALL YOUR FAULT
Me: Yes its all my fault, EVERYTHING is my fault!! I am fully responsible for ALL OF IT!! And since the only entity with that much responsibility is GOD, you need to get down on your knees and worship me NOW!!
(Disclaimer) This may be part of the reason she is my ex.....
11-07-2016 | 03:31 PM
#1592
Registered
Joined: Feb 2009
Posts: 8,356
Likes: 1,515
From: NW Michigan
Lot of truth to that. Coulda used just a tad more distance between Mr Robinson and the camera but WTH. He got the message across.
11-19-2016 | 06:06 PM
#1593
Thread Starter
Gold Member
Joined: Oct 2005
Posts: 11,691
Likes: 216
From: Olmsted Falls,Ohio Marblehead,Oh
Sweet new Intakes!
heads are being ported and intakes also, then valve jobs... then moving forward....
Still deciding pros and cons solid VS hydraulic lifters and if cost is worth changing..
[ATTACH=CONFIG]561840[/ATTACH]
heads are being ported and intakes also, then valve jobs... then moving forward....
Still deciding pros and cons solid VS hydraulic lifters and if cost is worth changing..
[ATTACH=CONFIG]561840[/ATTACH]
Last edited by Full Force; 11-19-2016 at 06:11 PM.
11-19-2016 | 06:22 PM
#1594
Registered
Joined: Nov 2004
Posts: 14,095
Likes: 3,685
From: On A Dirt Floor
Aren't those taller than the vic jr's ?
11-19-2016 | 06:39 PM
#1595
Registered
Joined: Oct 2013
Posts: 1,953
Likes: 2
From: rock Island wa
May the full force be be with you. God knows you've earned it.
11-19-2016 | 07:19 PM
#1596
Gold Member
Joined: Sep 2011
Posts: 2,643
Likes: 18
From: cleveland ohio
Any pics of the work old man Klien did on the intake of heads yet?
11-19-2016 | 07:39 PM
#1597
Thread Starter
Gold Member
Joined: Oct 2005
Posts: 11,691
Likes: 216
From: Olmsted Falls,Ohio Marblehead,Oh
11-19-2016 | 07:40 PM
#1598
Thread Starter
Gold Member
Joined: Oct 2005
Posts: 11,691
Likes: 216
From: Olmsted Falls,Ohio Marblehead,Oh
11-19-2016 | 07:40 PM
#1599
Thread Starter
Gold Member
Joined: Oct 2005
Posts: 11,691
Likes: 216
From: Olmsted Falls,Ohio Marblehead,Oh
11-20-2016 | 10:03 AM
#1600
Registered
Joined: Feb 2009
Posts: 8,356
Likes: 1,515
From: NW Michigan
id bet 40-50 hp gain with new intakes and port work. Most importantly your not going to continue slinging cam dust everywhere throughout and you'll have a good stable valvetrain. You have to make the decision on cam however I'd really consider going solid roller. It's always nice to know valves are open when there suppose to. Just my opinion but I hate hyd lifters. Did you inspect your roller bearings and clean. Time consuming I know but if you do use them I'd be a little concerned about cam lobe residue. May sound overly cautious I know but no need to take a chance. Less agressive lobe hyd will be fine I'm sure. I just have a personal preference and don't like to second question a valves position at a given moment. Keep us informed what cam you go with. No secrets now!!!
