Tunell raaammm!!!!
The following 12 users liked this post by ICDEDPPL:
87MirageIntruder (11-24-2021), flashgordon (11-25-2021), Gimme Fuel (11-24-2021), Griff (11-23-2021), KNOT-RIGHT (11-26-2021), OFFSHOREJOJO (11-28-2021), PQ290Enticer (10-19-2022), SB (11-23-2021), SecondWind (11-28-2021), sonicss42 (12-21-2021), TomZ (11-30-2021), TylerBurich (11-24-2021)
Top Answer
01-17-2022, 04:58 PM
Charter Member # 55
Charter Member
ICDEDPPL back in the house !!!!!!!
11-23-2021, 05:07 PM
#2
Registered
iTrader: (1)
Blow it , then ram it. Lol.
VIP Member
The following users liked this post:
ICDEDPPL (11-23-2021)
11-23-2021, 05:24 PM
#4
Registered
Ok where did you get the belt with the logo?!
The following users liked this post:
SB (11-23-2021)
The following 7 users liked this post by ICDEDPPL:
87MirageIntruder (11-24-2021), Diamond Dave (11-23-2021), Gimme Fuel (11-24-2021), KNOT-RIGHT (11-26-2021), PQ290Enticer (10-19-2022), SB (11-23-2021), TomZ (11-30-2021)
11-23-2021, 06:35 PM
#7
https://www.duplicolor.com/product/m...omotive-paint/
black smoke anodized metalcast, temp to 500 gas & oil resistent.
It's a little transparent, so any scratches prior to paint will show but the product is excellent
black smoke anodized metalcast, temp to 500 gas & oil resistent.
It's a little transparent, so any scratches prior to paint will show but the product is excellent
Last edited by outonsafari; 11-23-2021 at 06:37 PM.
The following 5 users liked this post by outonsafari:
getrdunn (11-24-2021), hoodoo (11-27-2021), ICDEDPPL (11-23-2021), SabrToothSqrl (10-24-2022), TomZ (11-30-2021)
11-23-2021, 06:41 PM
#8
Registered
Very Nice Dan! 
I have a similar set up with about 1/2 the Height on the runners. I might suggest to watch the fuel distribution closely, as there may be a tendency for a few cylinders to run on the lean side! AND be careful of some Fuel Injection gurus advise as this set up is out of most wheelhouse. Just my opinion.
I have a similar set up with about 1/2 the Height on the runners. I might suggest to watch the fuel distribution closely, as there may be a tendency for a few cylinders to run on the lean side! AND be careful of some Fuel Injection gurus advise as this set up is out of most wheelhouse. Just my opinion.
The following 2 users liked this post by abones:
articfriends (11-24-2021), getrdunn (11-24-2021)
The following 6 users liked this post by ICDEDPPL:
CDShack (11-24-2021), Gimme Fuel (11-24-2021), hogie roll (11-24-2021), OFFSHOREJOJO (11-28-2021), Payton (12-26-2021), PQ290Enticer (10-19-2022)
11-23-2021, 07:25 PM
#10
Very Nice Dan! I have a similar set up with about 1/2 the Height on the runners. I might suggest to watch the fuel distribution closely, as there may be a tendency for a few cylinders to run on the lean side! AND be careful of some Fuel Injection gurus advise as this set up is out of most wheelhouse. Just my opinion.
I have a similar set up with about 1/2 the Height on the runners. I might suggest to watch the fuel distribution closely, as there may be a tendency for a few cylinders to run on the lean side! AND be careful of some Fuel Injection gurus advise as this set up is out of most wheelhouse. Just my opinion.
