![]() |
O2 sensors and salt air is definitely a concern. If your tail pipes are going out the transom, and your boating in salt water, your o2 sensors will not last forever and it will end your day if they go bad. That salt air and moisture will work it's way back through the dry portion of your exhaust. Boating in fresh water much less of a concern, but I personally think moisture does work it's way back into the dry portion of the exhaust, and after time, will kill an o2, and potentially your motor. I would tune it on the safe side, and then pull those o2 sensors out and plug the holes. If some day your feeling like some more power, plug them back in and start playing with it.
|
Originally Posted by Ryanw10
(Post 4928130)
O2 sensors and salt air is definitely a concern. If your tail pipes are going out the transom, and your boating in salt water, your o2 sensors will not last forever and it will end your day if they go bad. That salt air and moisture will work it's way back through the dry portion of your exhaust. Boating in fresh water much less of a concern, but I personally think moisture does work it's way back into the dry portion of the exhaust, and after time, will kill an o2, and potentially your motor. I would tune it on the safe side, and then pull those o2 sensors out and plug the holes. If some day your feeling like some more power, plug them back in and start playing with it.
This is exactly where we are. Tune is conservative and safe. WBO2 is out, the ports plugged and the cable coiled and buttoned up. I have the sensor, sensor socket and 3/8 breaker bar, and an old 10mm Allen wrench for the O2 port plugs in a ziplock on the boat. I’ll have the laptop charged and with me for the first several trips, and the tuner on speed dial. This boat will never see salt water as long as we own it. Just…. No. But I hear ya loud and clear on the water/WBO2 thing. Thanks. Brad. |
The Eddie marine engines I`m getting are open loop.
|
Originally Posted by ICDEDPPL
(Post 4928138)
The Eddie marine engines I`m getting are open loop.
|
*you`re
|
Originally Posted by ICDEDPPL
(Post 4928157)
*you`re
|
Originally Posted by ICDEDPPL
(Post 4928115)
Why doesnt the 02 sensor read? To read plugs you have to start with a fresh set, go wot shut off , "read" plugs (I couldn`t ever tell anything ) then what about midrange how you read plugs there?
When there is a o2 available why not tune off that? It`s by far the most accurate annd super easy way.
Originally Posted by ICDEDPPL
(Post 4928115)
Running open loop doesnt have the system account for weather, temps, etc it`s basically a carburetor at that point. The whole point of Holley(for me anyways) is to have it compensate from 1500rpm onward.
|
Originally Posted by underpsi68
(Post 4928294)
02 is not the most accurate way. It is super easy, yes. Must accurate way is the read the plugs, more work by far.
100% incorrect. EFI will make fueling adjustments by using the sensors and what is programmed in the ecu/tune. Not even close to a carburetor. It won't make addition adjustments on top of the sensors if the 02's are turned off. I personally limit my 02 correction to 4% for idle / p/t and have 02 correction turned off at higher loads. If you 02's are correcting 10% or more, your tune is way off IMO. Plus, as I’m told, the HP has a barometer, so it will, in fact, compensate for changes in weather and elevation. Thanks. Brad. |
Originally Posted by Brad Christy
(Post 4928297)
UnderPSI,
Plus, as I’m told, the HP has a barometer, so it will, in fact, compensate for changes in weather and elevation. Thanks. Brad. You're MAP and closed loop compensation accounts for that. |
Originally Posted by Rookie
(Post 4928298)
You were told wrong.
You're MAP and closed loop compensation accounts for that. https://cimg6.ibsrv.net/gimg/www.off...78b31cced3.png It might be a matter of semantics, but, it does, in fact, account for air density changes, like a barometer. Thanks. Brad. |
| All times are GMT -5. The time now is 02:16 AM. |
Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.