Offshoreonly.com - Search Results
Offshoreonly.com

Go Back  Offshoreonly.com > Search Forums
Reload this Page >

Search Results

Register
FAQ
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: Baja525EFI
Showing results 1 to 16 of 16
Search took 0.00 seconds.
Forum: Fountain
10-29-2010, 07:10 PM
Replies: 32
Views: 5,121
Posted By Baja525EFI

Trust me, the dude is a crook. He screwed a...

Trust me, the dude is a crook. He screwed a buddy of mine big time. I know all of the facts but it's not my place to list them here. I wouldn't recommend anyone buy anything from him. If you buy...
Forum: Fountain
10-17-2010, 02:53 PM
Replies: 32
Views: 5,121
Posted By Baja525EFI

Beware of Ducky's

Jr. is a crook
Forum: Baja
08-29-2010, 06:58 PM
Replies: 12
Views: 1,957
Posted By Baja525EFI

2010 23' OL w/496HO

Anyone know what the top speed is? Thanks.
Forum: Drives and Lower Units
08-29-2010, 02:59 PM
Replies: 15
Views: 3,670
Posted By Baja525EFI

Dick, I am pretty sure I am replacing like with...

Dick, I am pretty sure I am replacing like with like. Coupler was the same when side by side. So were the yokes on the drives. Old yoke separated just above the splines then spun around in the...
Forum: General Q & A
08-27-2010, 09:00 PM
Replies: 18
Views: 2,521
Posted By Baja525EFI

Hope it's not what happened to me.......upper...

Hope it's not what happened to me.......upper gears shredded in xr drive. Drive stopped dead. Engine kept spinning snapping the input shaft and wrecking the u joints and coupler too. Bought a new...
Forum: Drives and Lower Units
08-25-2010, 06:22 AM
Replies: 15
Views: 3,670
Posted By Baja525EFI

I set up 2 - 2X4s that create a level runway to...

I set up 2 - 2X4s that create a level runway to slide the drive on. Also use a bottle jack on the transom end of the set up to make small adjustments. Will use the trailer neck to make sure...
Forum: Drives and Lower Units
08-23-2010, 04:49 PM
Replies: 15
Views: 3,670
Posted By Baja525EFI

Splines are aligned. Did change the coupler but...

Splines are aligned. Did change the coupler but used same type - long hub HP one that comes on XR.

1" space is the distance between drive and helmet mating surfaces. I am almost...
Forum: Drives and Lower Units
08-22-2010, 03:28 PM
Replies: 15
Views: 3,670
Posted By Baja525EFI

I think my gimbal bearing and coupler are...

I think my gimbal bearing and coupler are aligned. The tool slides in easily. But that axis is not be directly centered in the bellhousing. Hence the drive will slide on within an inch of mating...
Forum: Drives and Lower Units
08-21-2010, 11:17 AM
Replies: 15
Views: 3,670
Posted By Baja525EFI

Install Question

Speaking of Bravo XR stuff, I an trying to install my drive. I get it to about 1" to go and can't go any further. Sounds like U joints bottoming out. Suggestions?
Forum: Drives and Lower Units
07-18-2010, 11:57 AM
Replies: 22
Views: 4,502
Posted By Baja525EFI

How much would the Arneson set me back?

How much would the Arneson set me back?
Forum: Drives and Lower Units
07-18-2010, 10:50 AM
Replies: 11
Views: 1,394
Posted By Baja525EFI

Did get the drive off. Took a peek under the top...

Did get the drive off. Took a peek under the top cap. Looks like I am missing a few teeth from the bottom horizontal gear. Metal chips here and there.

So do I rebuild or get a new one? Does...
Forum: Drives and Lower Units
07-17-2010, 03:34 PM
Replies: 22
Views: 4,502
Posted By Baja525EFI

how much is the scx/sc combo? Is is a direct...

how much is the scx/sc combo? Is is a direct bolt on for the xr? thanks.
Forum: Swap Shop
07-17-2010, 03:30 PM
Replies: 6
Views: 1,024
Posted By Baja525EFI

still available?

still available?
Forum: Drives and Lower Units
07-17-2010, 02:49 PM
Replies: 11
Views: 1,394
Posted By Baja525EFI

So I bumped the starter a few times until I was...

So I bumped the starter a few times until I was able to slide the drive off. Here's the damage - I am missing a few inches off the shaft that used to mate with the coupler, coupler toasted, one...
Forum: Drives and Lower Units
07-11-2010, 01:54 PM
Replies: 11
Views: 1,394
Posted By Baja525EFI

I attempted to remove the drive but it will only...

I attempted to remove the drive but it will only release about 1/2" and then stops dead. It seems that something inside is stopping it from coming out. I have removed drives before and never had...
Forum: Drives and Lower Units
07-11-2010, 09:42 AM
Replies: 11
Views: 1,394
Posted By Baja525EFI

XR Advice Needed

I was cruising along at about 4000K RPMs minding my own business when bad things happened. I am not sure what happened first - gimbal bearing, uppers, u-joint, coupler, etc. After shutting down,...
Showing results 1 to 16 of 16


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.