Offshoreonly.com - Search Results
Offshoreonly.com

Go Back  Offshoreonly.com > Search Forums
Reload this Page >

Search Results

Register
FAQ
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: tutzone
Showing results 1 to 24 of 24
Search took 0.00 seconds.
Forum: General Q & A
06-23-2015, 04:21 PM
Replies: 48
Views: 4,643
Posted By tutzone

Smitty,The shop set the timing at 34 and will...

Smitty,The shop set the timing at 34 and will check it again before and after they do a water test tomorrow.
Forum: General Q & A
06-23-2015, 04:18 PM
Replies: 48
Views: 4,643
Posted By tutzone

I brought my boat back to the shop today.He said...

I brought my boat back to the shop today.He said he was going to do a leak down test and then a water test,with a fuel pressure gauge hooked up to see if its getting enough fuel.I put my 24 pitch...
Forum: General Q & A
06-22-2015, 08:44 PM
Replies: 48
Views: 4,643
Posted By tutzone

SB The motor was bored 030" over.

SB The motor was bored 030" over.
Forum: General Q & A
06-22-2015, 08:35 PM
Replies: 48
Views: 4,643
Posted By tutzone

Sb They didn't change the chip from 5200.The new...

Sb They didn't change the chip from 5200.The new box has a 4000,6000 or 8000 chip.I wasn't close to 5200 so i didn't even think twice about that.I will put a old hydro 24 pitch on tomorrow and put...
Forum: General Q & A
06-22-2015, 08:31 PM
Replies: 48
Views: 4,643
Posted By tutzone

Glenamy,The torque went from 592 @ 4600 to 536 @...

Glenamy,The torque went from 592 @ 4600 to 536 @ 5550.Drew555 I don't know 100% if this is my dyno sheet other than my name and motor info on it.I was not there when the engine was dynoed.Is it...
Forum: General Q & A
06-22-2015, 04:53 PM
Replies: 48
Views: 4,643
Posted By tutzone

Stock heads with new valves,springs,etc.

Stock heads with new valves,springs,etc.
Forum: General Q & A
06-22-2015, 02:41 PM
Replies: 48
Views: 4,643
Posted By tutzone

No i didn't.I will have them look into that...

No i didn't.I will have them look into that tomorrow.
Forum: General Q & A
06-22-2015, 02:24 PM
Replies: 48
Views: 4,643
Posted By tutzone

I am bringing it back to the engine builder...

I am bringing it back to the engine builder tomorrow.Some of the new parts used are ss intake valves,inconel exhaust valves,srp forged pistons,hastings piston rings,cam motion cam,m77 connecting rod...
Forum: General Q & A
06-22-2015, 01:05 PM
Replies: 48
Views: 4,643
Posted By tutzone

No i didn't.The fastest running prop was a 27...

No i didn't.The fastest running prop was a 27 pitch mach prop.Since that,its been twisted and repaired a couple of times.That is why i bought a new hydromotive.
Forum: General Q & A
06-22-2015, 12:52 PM
Replies: 48
Views: 4,643
Posted By tutzone

I was told the cam is made by cam motion

I was told the cam is made by cam motion
Forum: General Q & A
06-22-2015, 12:45 PM
Replies: 48
Views: 4,643
Posted By tutzone

The carb was rebuilt.I can't remember the brand...

The carb was rebuilt.I can't remember the brand for the cam but it's definitely more aggressive.
Forum: General Q & A
06-22-2015, 12:40 PM
Replies: 48
Views: 4,643
Posted By tutzone

I am spinning the new prop @ 4600 rpm's.The prop...

I am spinning the new prop @ 4600 rpm's.The prop is not the issue.I had them replace my msd ignition box with a new one and the distributor as well.I have not done a compression check again since the...
Forum: General Q & A
06-22-2015, 12:07 PM
Replies: 48
Views: 4,643
Posted By tutzone

I am running a brand new hydromotive 25 pitch...

I am running a brand new hydromotive 25 pitch prop.I was spinning a 27 pitch mach prop before the rebuild.
Forum: General Q & A
06-22-2015, 12:03 PM
Replies: 48
Views: 4,643
Posted By tutzone

It was before i had the motor rebuilt.

It was before i had the motor rebuilt.
Forum: General Q & A
06-22-2015, 11:47 AM
Replies: 48
Views: 4,643
Posted By tutzone

Help with a newly rebuilt HP 500

I just had my HP 500 rebuilt from a reputable engine builder in my area.The entire engine was gone through will all new parts,cam,pistons, rings,etc.The engine was tuned and run on the dyno.The peak...
Forum: Fountain
04-22-2012, 06:54 PM
Replies: 6
Views: 2,948
Posted By tutzone

bolster seat problem

My bolster seats were working fine before i put my 1995 27 fever away for the winter.Now comes spring and there is no power at all.I checked the fuses under the dash and the circuit breakers.Any...
Forum: Fountain
04-15-2011, 08:31 AM
Replies: 18
Views: 3,875
Posted By tutzone

I have a hp500 running in a 27 Fountain.I was...

I have a hp500 running in a 27 Fountain.I was running a 27 x 14 1/2 mach @ 76 mph @5100 rpm's.The prop got damaged and i sent it to bblades for repairs.When i got the prop back i now run 69 mph @...
Forum: General Q & A
04-30-2009, 09:11 PM
Replies: 32
Views: 17,907
Posted By tutzone

The engine has 250 hours on it.

The engine has 250 hours on it.
Forum: General Q & A
04-30-2009, 09:08 PM
Replies: 32
Views: 17,907
Posted By tutzone

I am looking for educated opinions not smart ass...

I am looking for educated opinions not smart ass responses.Thanks for the replies.
Forum: General Q & A
04-30-2009, 07:48 PM
Replies: 32
Views: 17,907
Posted By tutzone

Unhappy The engine builder came and took a look today and...

The engine builder came and took a look today and said there was very minimal scoring and that it was normal and nothing to be concerned about.He was more concerned about the slight darkening spots...
Forum: General Q & A
04-29-2009, 02:46 PM
Replies: 32
Views: 17,907
Posted By tutzone

Angry I am livid!!!!!!!!!!I went to the marina...

I am livid!!!!!!!!!!I went to the marina today.The owner and i had a look at the cylinder walls and neither one of us saw or felt any scoring!!!!!!!I do not understand why his mechanic would say this...
Forum: General Q & A
04-27-2009, 10:14 AM
Replies: 32
Views: 17,907
Posted By tutzone

I am going tomorrow to have a look.I will take...

I am going tomorrow to have a look.I will take pictures and post them.Thanks for the responses!
Forum: General Q & A
04-26-2009, 03:25 PM
Replies: 32
Views: 17,907
Posted By tutzone

Unhappy scored cylinder walls

I have a carb hp 500 with 250 hours on it.I wanted to get the heads redone as recommened by many people with this motor.To my surprise i was told that there is some scoring on each cylinder wall.I...
Forum: Fountain
03-14-2005, 08:00 PM
Replies: 4
Views: 1,196
Posted By tutzone

Red face fountain logo

Does anyone know where i can get a template for the fountain logo?I am redoing my interior and want to put the fountain logo on the hatch cover and the back of the front seats.Any help would be...
Showing results 1 to 24 of 24


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.