Offshoreonly.com - Search Results

Search: Posts Made By: rednourdj

Showing results 1 to 11 of 11
Search took 0.00 seconds.

Forum: General Q & A

03-09-2010, 08:16 PM

Replies: 10

adding oil cooler help

Views: 1,912

Posted By rednourdj

I would run to the filter first then the oil...

I would run to the filter first then the oil cooler. Reason being the oil is hotter and filtered easier, then to the cooler and into the engine. Run an adapter to a remote filter housing and into...

Forum: General Q & A

03-08-2010, 04:49 PM

Replies: 17

Has anyone personally installed a GM Marine 502 Base engine?

Views: 10,420

Posted By rednourdj

My expert racer/engine guru says take both...

My expert racer/engine guru says take both bypasses out, tap and plug the outerhole and run a WIX racing filter.I have the Mercury oil line adapter on my BB, be careful not to overtighten the hollow...

Forum: General Q & A

03-08-2010, 02:58 PM

Replies: 34

454 vs 489

Views: 24,256

Posted By rednourdj

Hey Guy's, fwiw, it took me two years to find a...

Hey Guy's, fwiw, it took me two years to find a genV 502 block. Few and far between. The good news, I got it for $750.00. On my way to a blown 540ci, chiller on the way. The rear seal adapter worked...

Forum: General Q & A

01-10-2009, 11:11 AM

Replies: 5

525SC maintenance questions

Views: 4,298

Posted By rednourdj

Ranger, you should consult your manual on blower...

Ranger, you should consult your manual on blower oil as different manufacturers use different types of oil. Kenne Belle uses Red Line synthetic SAE 50, B&M/Holley uses 75-80 gear oil or equivalent so...

Forum: Swap Shop

01-09-2009, 12:30 PM

Replies: 3

2 sets of stcck Merc 575 SCi pistons

Views: 911

Posted By rednourdj

Hey Vinney. Are they dished and what rod lentgh?...

Hey Vinney. Are they dished and what rod lentgh? I am going to build a 540 in the future with a huffer from my excisting engine. I need a Gen V 502 block and pistons, will be using my current...

Forum: General Q & A

01-09-2009, 11:47 AM

Replies: 2

J&S Electronics

Views: 753

Posted By rednourdj

EZ, dig a little deeper into their site and you...

EZ, dig a little deeper into their site and you will find one that is specificaly for marine/race applications. The prices don't look too bad either comparing to a 6m2 msd box, plus it's adjustable....

Forum: General Boating Discussion

01-08-2009, 05:59 PM

Replies: 15

Opinions on Arriva boats?

Views: 71,561

Posted By rednourdj

Well, I think they have the nicest lines for...

Well, I think they have the nicest lines for their time. Mine does 70mph with a mirage plus 25P @ 4800 rpm.

Forum: General Q & A

01-08-2009, 01:34 PM

Replies: 2

J&S Electronics

Views: 753

Posted By rednourdj

J&S Electronics

Hey all, Has anyone used or heard of J&S products. Here is a link to thier web site. www.jandssafeguard.com. I am curious because I would like to hear from other users before I make this investment....

Forum: General Q & A

01-08-2009, 01:19 PM

Replies: 121

454 magnum problems help please

Views: 28,168

Posted By rednourdj

Griff, LMFAO. I concur.

Griff, LMFAO. I concur.

Forum: General Q & A

01-08-2009, 12:23 PM

Replies: 42

standard crane or summitt roller rocker???

Views: 8,266

Posted By rednourdj

I put Scorpions in my 490. 1.7 and 1.8 ratios. I...

I put Scorpions in my 490. 1.7 and 1.8 ratios. I got them from Clay Smith Cams and if I remember right, I paid less than $300.00 for them. Holding up just fine and they're made in the USA. Pt# for...

Forum: General Q & A

01-04-2009, 06:07 PM

Replies: 17

Max EGT

Views: 3,896

Posted By rednourdj

egt's

Hi guy's. Just signed up today and was curios as to what others were running for temps.
I have a genV 454 stroked to 490 w/a holley 420 (no chiller yet) and a pair of holley 800's, Clay Smith 306...

Showing results 1 to 11 of 11