Offshoreonly.com - Search Results
Offshoreonly.com

Go Back  Offshoreonly.com > Search Forums
Reload this Page >

Search Results

Register
FAQ
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: TylerBurich
Showing results 1 to 11 of 11
Search took 0.02 seconds.
Forum: Formula
02-01-2021, 01:16 PM
Replies: 282
Views: 48,318
Posted By TylerBurich

I should rephrase my reply to mean that if the...

I should rephrase my reply to mean that if the quench isn't nailed down then the chance for knock is going to be much higher thus requiring less total timing and higher octane fuels which really...
Forum: Formula
02-01-2021, 11:18 AM
Replies: 282
Views: 48,318
Posted By TylerBurich

I don't believe the efficiency of the chamber...

I don't believe the efficiency of the chamber means squat if you don't get the quench right first. I think you are on the right track, hopefully someone smarter than me has some definitive...
Forum: Formula
01-09-2021, 09:32 AM
Replies: 282
Views: 48,318
Posted By TylerBurich

Don't get too hung up on dyno power numbers. I...

Don't get too hung up on dyno power numbers. I like the dyno for finding problems that can be remedied before you take all the time to reinstall them in the boat. I think you will like your gains...
Forum: Formula
01-06-2021, 11:25 AM
Replies: 282
Views: 48,318
Posted By TylerBurich

Smokey Yunick devotes an entire page in his book...

Smokey Yunick devotes an entire page in his book "Power Secrets" to quench. His guideline is .040" for all around performance in a 4" bore engine. Maybe add a few thou for 4.500" bore but sticking...
Forum: Formula
01-06-2021, 10:01 AM
Replies: 282
Views: 48,318
Posted By TylerBurich

What amount of quench are you shooting for? I...

What amount of quench are you shooting for? I believe if you focus on that your dynamic compression shouldn't be as much of an issue.
Forum: Formula
11-02-2020, 08:23 AM
Replies: 282
Views: 48,318
Posted By TylerBurich

Tom, did you decide on lifters yet or did I miss...

Tom, did you decide on lifters yet or did I miss that part?
Forum: Formula
10-13-2020, 08:51 AM
Replies: 282
Views: 48,318
Posted By TylerBurich

Which Crowers were you looking at? I'm digging...

Which Crowers were you looking at? I'm digging the shaft mount bushed tip, they will do any ratio you want. I was looking at these for my merlin 3's .....
Forum: Formula
10-09-2020, 08:16 AM
Replies: 282
Views: 48,318
Posted By TylerBurich

Tom I really like our 500efi cams. I agree with...

Tom I really like our 500efi cams. I agree with your statement that the good cylinder heads make them seem bigger. Easy to get them to idle solid for shifting gears and still run up well into the...
Forum: Formula
09-16-2020, 10:02 AM
Replies: 282
Views: 48,318
Posted By TylerBurich

If it is that far gone just grind a flat spot on...

If it is that far gone just grind a flat spot on the head or what is left and center punch it really good, drill the head and it will pop loose.
Forum: Formula
09-14-2020, 09:08 AM
Replies: 282
Views: 48,318
Posted By TylerBurich

What hydraulic steering is that? Is it add on or...

What hydraulic steering is that? Is it add on or full hydraulic to the helm?
Forum: Formula
09-01-2020, 11:51 AM
Replies: 282
Views: 48,318
Posted By TylerBurich

The fuel pickups in our 88 311 are rather small...

The fuel pickups in our 88 311 are rather small pipe thread in size i'm thinking 3/8" npt female at the tank fitting. Let me know what you end up doing for tank pickups I think you will need to...
Showing results 1 to 11 of 11


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.