36 Skater 1.24 or 1.35 Gears
10-24-2008, 06:04 PM
#61
Banned
are you wet sump or dry ?? X dimension ???
10-28-2008, 06:40 AM
#65
Banned
ditto on that and a call to Peter is alwayz helpfull .... give me a call when you get a few mins
10-28-2008, 06:46 AM
#66
Banned
That is a very good point also Bill , we have some dyno sheets that came with the motors that just dont seem to match and are set for a real dyno this friday (no correction factor B/S) to see where the 300 hp per side went ....
10-28-2008, 06:55 PM
#67
Registered
Thread Starter
Join Date: Jul 2002
Location: Yorba Linda,Ca.
Posts: 285
Likes: 0
Received 0 Likes
on
0 Posts
Props
Gatorone only what the Dyno sheets show for the one motor we took out and Dynoed 6 months ago.
1022 HP at 5900 RPM ( 996 HP at 6100 RPM)
978 Ft Lbs at 4600 RPM ( 861 Ft Lbs at 6100)
Air Temp 76 , 29.9 inches Barometric 700' elevation
Last weekend runs at 131 was air temp 87 1300 elevation, dry air (Lake Mead near Vegas) I know we loose HP on that lake.
So who knows for sure what's going on when I'm on the lake.
This 131 speed could have gone up with more time at that RPM (Ie let it run out farther but not much) and I did have a little throttle left.
I am going to send out the Props and have then scanned to tell us exactly what we have (they came with my 32 Skater I had before but they where used back then) ie: not exactly sure what they are as far as Cup and rake and are not labbed as far as i know.
1022 HP at 5900 RPM ( 996 HP at 6100 RPM)
978 Ft Lbs at 4600 RPM ( 861 Ft Lbs at 6100)
Air Temp 76 , 29.9 inches Barometric 700' elevation
Last weekend runs at 131 was air temp 87 1300 elevation, dry air (Lake Mead near Vegas) I know we loose HP on that lake.
So who knows for sure what's going on when I'm on the lake.
This 131 speed could have gone up with more time at that RPM (Ie let it run out farther but not much) and I did have a little throttle left.
I am going to send out the Props and have then scanned to tell us exactly what we have (they came with my 32 Skater I had before but they where used back then) ie: not exactly sure what they are as far as Cup and rake and are not labbed as far as i know.
10-29-2008, 11:04 AM
#69
Registered
Join Date: Dec 2006
Location: Tucson, AZ
Posts: 495
Likes: 0
Received 0 Likes
on
0 Posts
Gatorone only what the Dyno sheets show for the one motor we took out and Dynoed 6 months ago.
1022 HP at 5900 RPM ( 996 HP at 6100 RPM)
978 Ft Lbs at 4600 RPM ( 861 Ft Lbs at 6100)
Air Temp 76 , 29.9 inches Barometric 700' elevation
Last weekend runs at 131 was air temp 87 1300 elevation, dry air (Lake Mead near Vegas) I know we loose HP on that lake.
So who knows for sure what's going on when I'm on the lake.
This 131 speed could have gone up with more time at that RPM (Ie let it run out farther but not much) and I did have a little throttle left.
I am going to send out the Props and have then scanned to tell us exactly what we have (they came with my 32 Skater I had before but they where used back then) ie: not exactly sure what they are as far as Cup and rake and are not labbed as far as i know.
1022 HP at 5900 RPM ( 996 HP at 6100 RPM)
978 Ft Lbs at 4600 RPM ( 861 Ft Lbs at 6100)
Air Temp 76 , 29.9 inches Barometric 700' elevation
Last weekend runs at 131 was air temp 87 1300 elevation, dry air (Lake Mead near Vegas) I know we loose HP on that lake.
So who knows for sure what's going on when I'm on the lake.
This 131 speed could have gone up with more time at that RPM (Ie let it run out farther but not much) and I did have a little throttle left.
I am going to send out the Props and have then scanned to tell us exactly what we have (they came with my 32 Skater I had before but they where used back then) ie: not exactly sure what they are as far as Cup and rake and are not labbed as far as i know.
That sucks.....if it is with 1.35's, you are at 10%, which is getting there.Erik
10-29-2008, 02:47 PM
#70
VIP Member
VIP Member
