Skater Logo ???
02-25-2009, 10:29 PM
#41
Banned
Thread Starter
02-25-2009, 10:58 PM
#42
VIP Member
lol . . . look it up. Wikipedia or something 
__________________
Throttles- Cleveland Construction 377 Talon
08 OPA Class 1 National Champion
08 Class 1 Geico Triple Crown Champion
08 OPA High Points Champion
10 OPA Class 1 National Champion ( happy now Ed! )
Throttles- Cleveland Construction 377 Talon
08 OPA Class 1 National Champion
08 Class 1 Geico Triple Crown Champion
08 OPA High Points Champion
10 OPA Class 1 National Champion ( happy now Ed! )
02-25-2009, 11:40 PM
#44
that chick is ridiculously hot . . . .saw her in some ebay ads for boats
__________________
Throttles- Cleveland Construction 377 Talon
08 OPA Class 1 National Champion
08 Class 1 Geico Triple Crown Champion
08 OPA High Points Champion
10 OPA Class 1 National Champion ( happy now Ed! )
Throttles- Cleveland Construction 377 Talon
08 OPA Class 1 National Champion
08 Class 1 Geico Triple Crown Champion
08 OPA High Points Champion
10 OPA Class 1 National Champion ( happy now Ed! )
Last edited by glassdave; 02-25-2009 at 11:43 PM.
02-25-2009, 11:42 PM
#45
Banned
Thread Starter
02-26-2009, 05:26 PM
#46
Banned
Thread Starter
02-26-2009, 05:34 PM
#48
SWEET! . . . . . any more pics of that chick in post #43? 
just thought of something else. When you are done with the diamonds only pull off the #2 and #3 mask leaving the largest outer mask, that will allow you to double check the 1/4" edge/border highlights. If for some reason you want to change it i can cut a mask to block off just the main diamond plate part and you can correct it. I still have the cutfile with registration marks in place.
Man this is great . . . I'm just gonna phone in graphics from now on . . . this is way easier
just thought of something else. When you are done with the diamonds only pull off the #2 and #3 mask leaving the largest outer mask, that will allow you to double check the 1/4" edge/border highlights. If for some reason you want to change it i can cut a mask to block off just the main diamond plate part and you can correct it. I still have the cutfile with registration marks in place.
Man this is great . . . I'm just gonna phone in graphics from now on . . . this is way easier
__________________
Throttles- Cleveland Construction 377 Talon
08 OPA Class 1 National Champion
08 Class 1 Geico Triple Crown Champion
08 OPA High Points Champion
10 OPA Class 1 National Champion ( happy now Ed! )
Throttles- Cleveland Construction 377 Talon
08 OPA Class 1 National Champion
08 Class 1 Geico Triple Crown Champion
08 OPA High Points Champion
10 OPA Class 1 National Champion ( happy now Ed! )
Last edited by glassdave; 02-26-2009 at 05:43 PM.
02-26-2009, 05:54 PM
#49
Banned
Thread Starter
SWEET! . . . . . any more pics of that chick in post #43?
just thought of something else. When you are done with the diamonds only pull off the #2 and #3 mask leaving the largest outer mask, that will allow you to double check the 1/4" edge/border highlights. If for some reason you want to change it i can cut a mask to block off just the main diamond plate part and you can correct it. I still have the cutfile with registration marks in place.
Man this is great . . . I'm just gonna phone in graphics from now on . . . this is way easier
just thought of something else. When you are done with the diamonds only pull off the #2 and #3 mask leaving the largest outer mask, that will allow you to double check the 1/4" edge/border highlights. If for some reason you want to change it i can cut a mask to block off just the main diamond plate part and you can correct it. I still have the cutfile with registration marks in place.
Man this is great . . . I'm just gonna phone in graphics from now on . . . this is way easier
Sounds good Dave , if i have to i'll probably just use some 1/4" tape if i have to because those areas i talked about werent all that huge. Ill just see in the end when i pull it, off. thanks for your help its moving along pretty smooooothly now .
P.S. stop calling me so much at the shop, my dad thinks im not gettin anything done and says i'm not moving fast enough
... grasshopper
Last edited by RunninHotRacing163.1; 02-26-2009 at 06:09 PM.
