548 ci motors
 

$18, 500 each

889 hp@ 8 psi
Mark IV bowtie blocks.
548 ci
4.530 bore, 4.25 stroke
651 crane cam (244/256 632 lift 114 lsa)
Piston oilers
Spring oilers
Machining by Borowski Race engines
Fresh this spring from short block up.
2 year old boost referenced Quick fuel 1050 carbs
Canton 10 qt oil pans
Construction
* Six Trap Door Baffles
* Oil Recovery Pouch
* Crank Scraper
* Bolt In Slosh Baffle
* Built In Louvered Windage Tray
* Three 1/2" NPT Bungs
* Provision For our Pan Mounted Dipstick
* Powder Coating & Brass Plugs For Corrosion
Protection
Eagle cranks
JE pistons
Molnar Rods
Dart iron eagle 345 heads with 40 hrs worth of combustion chamber and port work done by High Flow Heads.
Ferrea super alloy exhaust valves
Competition plus intake valves
.135 wall Trend 3/8 pushrods
Stainless Crower rockers.
Intake: offset rockers for better valve pattern
Tool room springs
Stage 4 BDS 10-71 blower gone thru at Dyers. Restripped and replaced bearings 3 years ago.
Schumann High flow oil pumps
Daytona ignitions with map sensors. ( easily build 3D timming maps based on map/rpm/load/boost)
Daytona Boxes also have many other features like idle stabilization, start reatrd etc etc.
New MSD distributors
IMI HI TQ starters
Completely rewired and pre-wired for warning lights. (senders installed)
Water/oil temps, pressure and Fuel pressure.
Fuel set up for return to tank
Set up for pre oiler or easy oil changes with built in pump.
Brass seapumps
Hexadjust timing chains
Available with or without Drive Guardians ($2500 each)
8 plate bellhousing coolers for motor and trans
reason for sale: Boat sold without power
Ready to drop in, no corners cut on these builds whatsoever, ran perfect all summer.
Priced to sell


Edited: exhaust no longer available, price adjusted...

https://www.youtube.com/watch?v=S72CbYUxSvY ran great all summer

https://www.youtube.com/watch?v=PmvE2K9hB2A

CNC rottler machining


https://www.youtube.com/watch?v=_CkniqKr_uo

Idle great


https://www.youtube.com/watch?v=hDqAawtfF0g

Open to selling without bellhousing and exhaust

All that work and expense... Now what you going to do?

http://33outlaw.zenfolio.com/img/s/v-2/p428985154-4.jpg

http://33outlaw.zenfolio.com/img/s5/...35480960-4.jpg

http://33outlaw.zenfolio.com/img/s3/...75296650-4.jpg

http://33outlaw.zenfolio.com/img/s5/...22660662-4.jpg

http://33outlaw.zenfolio.com/img/s10...02775515-4.jpg

Cry a lot

Say it isn't so Dan

:bsflag::throw:

How much for the exhaust?

Not selling the exhaust till I find a buyer who doesn`t want it.. thanx

Rick you need some engines?? :D Make you a great deal.
There`s a boat in Sarnia ON I wanna see so I`ll even deliver .

i know it isn't ever gonna reach that point, and i hope it never does,the boat is to nice not to go intact
but i'm really wanting one of those #5's trans thru prop, gotta be a whole package
then i still don't know if i could swing it

I have a deposit on the boat minus power so I think it`s reached that point .


$17K each without bellhousings and Exhaust.

reach the point of being parted out is what i meant, it,s just too nice.

but (intact) minus engines is no biggie

glad you have an offer, hope it works out well and in a timely fashion,

dan

I would be interested in exhaust as well. I would be all over complete set up, already started building 2 new 565's

i know a little about these engines,THIS IS A VERY GOOD DEAL.

I did not realize new owner needs the exhaust , price adjusted accordingly.
Yes Mike it is a very good deal, thanx for building them, what a difference over the old set up.

http://33outlaw.zenfolio.com/img/s5/...79105702-3.jpg

http://33outlaw.zenfolio.com/img/s5/...21454469-4.jpg

All I need to do is pull em out for ya:D or you can see them run in the boat..

i only did shortblocks,you and joe did a nice job finishing them.

Damn Dan.. What happened? I thought you found the right setup and now its going? Hope things are okay.

Should have a buyer in Ohio, no?! :evilb: Best of luck on the next ride. One beautiful Cig you had there.

Thanks Dan but Al has me set up with my boat anchors . Hate to change them just got them to run right . But if it is last year it would have been a done deal .
Let me know when you are going to be In Sarnia maybe Al and I will take a road trip .
Cheers Rick G.

Leaving the Straightbottoms Behind ?

You spend thousands of hours and dollars to make sure everything is good to go and reliable and it finally was running like a clock.... then on a nice easy cruise I lost a prop and shaft, and on the way home it I blow a tire and my spare had a leak in it too... kinda the straw that broke the camels back.

I`ll probably regret this thou so...it is what it is

Everything else is good thou, thanx for asking
Right now I`m enjoying a larger bank account and free weekends, first time in 4 years

Sounds like everyday for me. I hook up the plow on plow truck. Of course the hydraulics don't work so I strap it up to get it to the shop to repair. I didn't have to go far so I didn't bother latching and hit the brakes at end of drive and the plow goes hydroplaning across road with a bunch of wires hanging out of the wire loom. I attempt to get plow back up onto mount and slipped and whacked my melon on the top of the plow. Road commission waiting for me as I was blocking majority of road. I finally get everything back in place with the exception of wiring harness. Now I go to leave and the fken battery was dead.

At least you have a choice to do as you please but needless to say I still gotta plow snow. Sometimes things just plain ol suck.

You have the rest of your life purchase more boats. Take your time and chill for a bit. I've been with and without a boat over 30 years to date. Just think now you can be that cool dude that flips your buddy a twenty dollar bill when filling up at the station. Haha... Had friends years ago that would do that and I'd tell them to just buy the beer. They'd have no clue how much fuel you'd go through.

Anyway good luck.

Dan.
Sometimes less (horsepower) is more.

Explain that...

More boating season
More money saved
More happy family
More practical

Probably one of the reasons C.C's are gaining popularity

http://33outlaw.zenfolio.com/img/s/v...50607682-4.jpg

http://33outlaw.zenfolio.com/img/s/v...92764477-4.jpg



Piston oilers



http://33outlaw.zenfolio.com/img/s6/...74781933-4.jpg


http://33outlaw.zenfolio.com/img/s/v...49243442-4.jpg

http://33outlaw.zenfolio.com/img/s12...09815025-4.jpg

http://33outlaw.zenfolio.com/img/s1/...49838269-4.jpg


http://33outlaw.zenfolio.com/img/s/v...19641544-3.jpg

Epoxy primer, pearl paint and clearcoat
 

http://33outlaw.zenfolio.com/img/s9/...93081364-4.jpg


http://33outlaw.zenfolio.com/img/s/v...89547857-4.jpg


http://33outlaw.zenfolio.com/img/s/v...60009904-4.jpg

http://33outlaw.zenfolio.com/img/s/v...06237877-4.jpg

http://33outlaw.zenfolio.com/img/s12...86813341-4.jpg

http://33outlaw.zenfolio.com/img/s5/...86813474-3.jpg

With stainless marine Exhaust it`s rigged to run water thru manifold first before motor to pre-heat cold lake Michigan water. No condensation issues and a great idle with warm water .

Standard bypass also available.

http://33outlaw.zenfolio.com/img/s1/...86813681-4.jpg

http://33outlaw.zenfolio.com/img/s2/...86813829-4.jpg

Trade for a pair of 05 525efi's with 185 hrs. have refresh / upgrade parts from Eddie Young ..Hd. gaskets, springs, bolts , they haven't been touched to this point

Sucks this boat is getting sold , but if you have any extra boat covers laying around, Im looking for one! LOL.....

That could work , trade plus some cash.

It's pretty obvious your very meticulous. You must have a lot of time into them. Look great!!!