WTB Gibson mufflers

Reply Subscribe

Thread Tools

03-07-2019, 10:13 PM

highplainsdrifter

Registered

Thread Starter

Join Date: Dec 2018

Posts: 99

Likes: 0

Received 3 Likes on 3 Posts

WTB Gibson mufflers

Anybody have the gibson bullet transom mount mufflers they want to sell?

Thanks,
Russ

03-08-2019, 06:26 AM

open87

Registered

iTrader: (2)

Join Date: Feb 2003

Location: Lafayette,La

Posts: 6,194

Likes: 68

Received 293 Likes on 107 Posts

I have 1 set of Aqua Power 5" $250 shipped UPS

03-08-2019, 06:50 AM

F-2 Speedy

Platinum Member

iTrader: (6)

Join Date: May 2012

Location: Midwest & T-Rock

Posts: 10,418

Likes: 412

Received 3,051 Likes on 1,357 Posts

Quote:

Originally Posted by highplainsdrifter

Anybody have the gibson bullet transom mount mufflers they want to sell?

Thanks,
Russ

send Bill 3 a pm I think he had a pair for sale

05-27-2019, 08:05 AM

Rhythm and Blues

VIP Member

VIP Member

Join Date: Mar 2008

Location: Maine

Posts: 875

Likes: 52

Received 67 Likes on 39 Posts

Quote:

Originally Posted by open87

I have 1 set of Aqua Power 5" $250 shipped UPS

Kind of an old thread here but how much pipe is required for full engagement and utilization for both clamps? Thanks.

05-27-2019, 10:03 PM

open87

Registered

iTrader: (2)

Join Date: Feb 2003

Location: Lafayette,La

Posts: 6,194

Likes: 68

Received 293 Likes on 107 Posts

Quote:

Originally Posted by Rhythm and Blues

Kind of an old thread here but how much pipe is required for full engagement and utilization for both clamps? Thanks.

Aqua power Ltd 5" set of mufflers 3 1/4" for clamp surface if put on to the stop tabs inside. $250 for 2 / $475 for 4 shipped UPS.

05-28-2019, 10:40 PM

Rhythm and Blues

VIP Member

VIP Member

Join Date: Mar 2008

Location: Maine

Posts: 875

Likes: 52

Received 67 Likes on 39 Posts

Quote:

Originally Posted by open87

Aqua power Ltd 5" set of mufflers 3 1/4" for clamp surface if put on to the stop tabs inside. $250 for 2 / $475 for 4 shipped UPS.

Thanks, appreciate that. I think your buddy messaged me on FB about a post I stared in there looking for mufflers. I have 4” tails and he said you did too and were using some sort of spacer? I’m curious if you just went to the end of the band clamps instead of the stops, then how much engagement would be needed? Thanks again.

05-29-2019, 08:12 AM

open87

Registered

iTrader: (2)

Join Date: Feb 2003

Location: Lafayette,La

Posts: 6,194

Likes: 68

Received 293 Likes on 107 Posts

05-29-2019, 08:18 AM

open87

Registered

iTrader: (2)

Join Date: Feb 2003

Location: Lafayette,La

Posts: 6,194

Likes: 68

Received 293 Likes on 107 Posts

1 3/4" on clamps. Must have been Dave? . If you need 4 I have 4. Only needed 2 , Made a deal on SSM V drive and still owe Mike 2 g's.. plenty of muff's out there , going to be a while for me now since I think I am going to put a notch in the bottom lol..

Fresh polish on them. $475 for all 4 shipped UPS.

05-29-2019, 06:26 PM

Rhythm and Blues

VIP Member

VIP Member

Join Date: Mar 2008

Location: Maine

Posts: 875

Likes: 52

Received 67 Likes on 39 Posts

Quote:

Originally Posted by open87

Thanks. Yeah it was Dave, I just looked back. The clamping dimension works for me. So, did you have them mounted on 4” tails w a spacer? I’m a little apprehensive but if I could come up w a foolproof way to mount them I could pull the trigger..

05-29-2019, 10:56 PM

#10

open87

Registered

iTrader: (2)

Join Date: Feb 2003

Location: Lafayette,La

Posts: 6,194

Likes: 68

Received 293 Likes on 107 Posts

Quote:

Originally Posted by Rhythm and Blues

https://www.hardin-marine.com/p-2700...aust-hose.aspx 4 1/2" has a outside diameter of 5 1/16" . Was planning on putting a cut which would be a 1/16" . Never called Stainless Marine to see if I could buy a piece of there material since it is a 1/2" thick that goes around my pipes with the stainless ring on transom.

Reply Share

First
Prev
1 / 2
Next
Last