Offshoreonly.com
Page 6 of 30
« First
4
5
6
7
8
16
Last »
Show 40 post(s) from this thread on one page

Offshoreonly.com (https://www.offshoreonly.com/forums/)
-   Active Thunder (https://www.offshoreonly.com/forums/active-thunder-30/)
-   -   Winter Project (https://www.offshoreonly.com/forums/active-thunder/219305-winter-project.html)

Thunderstruck 01-31-2010 05:44 PM
Originally Posted by flenner (Post 3035517)
Bilge looks great. I've been waiting two months for my new intakes to come in so I could finish my engine build. We finally got them Friday and yesterday got the first engine on the dyno. Took some time chasing and electrical gremlin. Ended up being my distributors. Final pull........637HP at 5600 rpm and peak torque was 686 at 4100 rpm. I can't say enough about my buddy Eric (owner of EB Marine) and Troy. I am very pleased with the results and they have been great threw out the whole thing.
That is a lot of HP. What is your setup????

Thunderstruck 01-31-2010 05:45 PM
1 Attachment(s)
2 Melling HV77's with pickups freshly welded.

laszlo01 01-31-2010 07:15 PM
Originally Posted by flenner (Post 3035517)
Bilge looks great. I've been waiting two months for my new intakes to come in so I could finish my engine build. We finally got them Friday and yesterday got the first engine on the dyno. Took some time chasing and electrical gremlin. Ended up being my distributors. Final pull........637HP at 5600 rpm and peak torque was 686 at 4100 rpm. I can't say enough about my buddy Eric (owner of EB Marine) and Troy. I am very pleased with the results and they have been great threw out the whole thing.
Nice numbers on a single N/A motor.

Thunderstruck 02-02-2010 09:16 PM
1 Attachment(s)
Finished the bilge tonight. Start putting the bilge back together tomorrow, waiting on some motor parts. Rod Bearings, balancers, timing gear bolts and oil pump intermediate shafts.

Powdercoating finished will pick up in the am.

Thunderstruck 02-02-2010 09:19 PM
Somebody stop mmmeee!

laszlo01 02-02-2010 09:24 PM
Originally Posted by Thunderstruck (Post 3037435)
Finished the bilge tonight. Start putting the bilge back together tomorrow, waiting on some motor parts. Rod Bearings, balancers, timing gear bolts and oil pump intermediate shafts.

Powdercoating finished will pick up in the am.
Very nice job, looking good.

Thunderstruck 02-02-2010 09:34 PM
Originally Posted by laszlo01 (Post 3037438)
Very nice job, looking good.
Well, how's the motors coming along Las??

Thunderstruck 02-02-2010 09:36 PM
Oops, also waiting on springs, retainers, locks and lifters from our bestest valve train guru, RMBuilder.

laszlo01 02-02-2010 09:54 PM
Originally Posted by Thunderstruck (Post 3037446)
Well, how's the motors coming along Las??
Very well, on the dynos by the end of the month, redoing the bilge as well right now, wish spring was closer but will be ready as soon as the weather gets here. What you doing on your motor project ?

rssteiny 02-03-2010 07:45 AM
Originally Posted by Thunderstruck (Post 3037435)
Finished the bilge tonight. Start putting the bilge back together tomorrow, waiting on some motor parts. Rod Bearings, balancers, timing gear bolts and oil pump intermediate shafts.

Powdercoating finished will pick up in the am.
Looks good, your on a roll dont stop now:evilb:


All times are GMT -5. The time now is 09:08 PM.
Page 6 of 30
« First
4
5
6
7
8
16
Last »
Show 40 post(s) from this thread on one page


Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.