Offshoreonly.com
Page 6 of 46
« First
4
5
6
7
8
16
Last »
Show 40 post(s) from this thread on one page

Offshoreonly.com (https://www.offshoreonly.com/forums/)
-   Cigarette (https://www.offshoreonly.com/forums/cigarette-32/)
-   -   Bullet rebuild (https://www.offshoreonly.com/forums/cigarette/279176-bullet-rebuild.html)

caseyh 09-13-2013 02:28 PM
Originally Posted by tcwcar (Post 3994859)
I was wondering how its going, glad to see your back on it, these "projects" take so much time believe me I know, but if your doing it yourself like me the rewards are great, not only will you know every inch of your boat, you'll never have to pay someone (unless you want to) to do work on your boat, and the pride you have after you start completing little projects that help finish the whole job is priceless....hey I wanted to be on the water this summer, it wasn't in the cards I guess, just to much to do, and I'm to much of perfectionist, but the boats done the way I want it done, and I did it, not someone else, and I will be on the water in the spring,...keep going man......

Would love to say I am doing it All my slef, but lighting jack customs is playing a big roll in helping out.

5050 09-16-2013 08:49 PM
Looking good Cassey. Hope to come down next yr and run my 38avs there and make a trip to bourbon st. Nice to see you taking my old boat to a new level. You'll have to post dyno sheets when you overhaul motors!

caseyh 09-27-2013 08:12 AM
Thanks it's going slow. Almost have the little issue fixed and it will be back in full swing. Got the trans back from huber marine they are now 1150s with all the entra stuff you can do to them.

caseyh 11-25-2013 11:03 AM
Looks like we are pulling the tanks on the boat ! The never ending project!

carter38 11-25-2013 03:21 PM
Originally Posted by caseyh (Post 4032425)
Looks like we are pulling the tanks on the boat ! The never ending project!
Man that sux. Spray in bed liner the floor panels while out looks great all back together.

caseyh 01-23-2014 02:14 PM
2 Attachment(s)
Been busy. Tanks are out cleaned up so is that part of the boat ready to go back in with new foam.
Sanding more in the buildge so it's a mess again. [ATTACH=CONFIG]517049[/ATTACH]

2manyprojcts 01-23-2014 02:52 PM
Casey I want to pull my tanks do you have any more pictures of how they came out and how much glass you had to remove. thanks Keith

caseyh 01-23-2014 03:23 PM
Originally Posted by 2manyprojcts (Post 4062063)
Casey I want to pull my tanks do you have any more pictures of how they came out and how much glass you had to remove. thanks Keith
You have to cut the lip that hangs over the at the back bulk head. Mine was cut higher up then needed. But it was done that way to make sure nothing need addressing while it was getting work done. If you look at that First pic you can see it was cut up About 6" above the floor. Then remove the foam if it's even holding it in. They should come right up.

jbraun2828 01-23-2014 03:26 PM
Originally Posted by 2manyprojcts (Post 4062063)
Casey I want to pull my tanks do you have any more pictures of how they came out and how much glass you had to remove. thanks Keith
How are you ever going to get that thing done if you keep taking more chit out of it ha ha

2manyprojcts 01-23-2014 03:37 PM
thank you so much


All times are GMT -5. The time now is 03:55 PM.
Page 6 of 46
« First
4
5
6
7
8
16
Last »
Show 40 post(s) from this thread on one page


Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.