Offshoreonly.com
Page 10 of 14
« First
8
9
10
11
12
Last »
Show 40 post(s) from this thread on one page

Offshoreonly.com (https://www.offshoreonly.com/forums/)
-   General Boating Discussion (https://www.offshoreonly.com/forums/general-boating-discussion-51/)
-   -   Dyno day for the stroker!! (https://www.offshoreonly.com/forums/general-boating-discussion/326433-dyno-day-stroker.html)

iliveonanisland 06-04-2015 07:45 PM
Originally Posted by Awash (Post 4313334)
Well if the OP would of come back with a Dyno chart we wouldn't have had to trash the place! I think it went bad after the photo of Brandon eating popcorn but it may have started a little before that.........
X2. It prob only made 400 ponies and he is toó embarrassed to post the dyno sheet lol

iliveonanisland 06-04-2015 07:47 PM
Originally Posted by cig92 (Post 4313339)
I have a 68 z 28 cross ram with factory headers and the cam card suggested shifting at 5,200-8,400 rpm. the car doesn't stop pulling at high rpm, it just wants to keep on going. if gm is telling you 8400 then im sure there is a safety factory built in there. i wouldn't doubt for one minute that motor will run over 10,000 rpm.
Post up some pics a dat bad mofo!

Black Baja 06-04-2015 07:56 PM
Originally Posted by SB (Post 4313325)
BB - DM ? I don'tfollowthe Aussie stuff much,but I did see when a few Aussie's enlisted DM for some work a while back.
Tommy Slawko.

cig92 06-04-2015 09:00 PM
Originally Posted by iliveonanisland (Post 4313342)
Post up some pics a dat bad mofo!
wish i could but i cant post pics here. it's a yellow with black stripes rs car, pre z 28 badge. the early ones only said 302 down in the front quarter. this car was a test mule for gm and its cross ram manifold. it has one of the 5 gm test manifolds with devcon wiring in it instead of the an actual cast manifold. it also has the test carbs that are 585's instead of the 600's that were used on the other 200ish manifolds. i'm told the headers are 1 of 22 sets produced for the cross ram.

12meter joe 06-04-2015 09:01 PM
Originally Posted by payuppsucker (Post 4312989)
Where the hell have you been for the past several months brother? Good to hear from you.
Had to take a little break but I'm back! :party-smiley-048:

12meter joe 06-04-2015 09:06 PM
Originally Posted by iliveonanisland (Post 4312983)
What made up that combinación and what was it in?
Seriously?

iliveonanisland 06-04-2015 09:17 PM
Originally Posted by 12meter joe (Post 4313371)
Seriously?
Ive se en some really trippy sbc stuff... Ive seen a kawi triple with a cylinder lopped off to make a class size límit so anythings posible bro f1 cara are spinning 20k revs

iliveonanisland 06-04-2015 09:27 PM
Originally Posted by cig92 (Post 4313366)
wish i could but i cant post pics here. it's a yellow with black stripes rs car, pre z 28 badge. the early ones only said 302 down in the front quarter. this car was a test mule for gm and its cross ram manifold. it has one of the 5 gm test manifolds with devcon wiring in it instead of the an actual cast manifold. it also has the test carbs that are 585's instead of the 600's that were used on the other 200ish manifolds. i'm told the headers are 1 of 22 sets produced for the cross ram.
What an awesome sled bro

DBleil89 06-05-2015 06:31 AM
I'm willing to bet he wasn't at the hp numbers he wanted ot expected. I'm running 10.4:1 in my motor that is close to his build and the machine shop is only estimating it at 550-600 hp. He was probably right around 500.

Budman II 06-05-2015 08:09 AM
Originally Posted by iliveonanisland (Post 4313340)
X2. It prob only made 400 ponies and he is toó embarrassed to post the dyno sheet lol
Either that or it scattered on the dyno. :eek:


All times are GMT -5. The time now is 02:52 AM.
Page 10 of 14
« First
8
9
10
11
12
Last »
Show 40 post(s) from this thread on one page


Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.