bunks on boat trailers
#21
Registered
Join Date: Dec 2003
Location: Los Angeles California
Posts: 8,306
Likes: 0
Received 2 Likes
on
2 Posts
You may be right about that Chart.... sometimes why things are made a certain way doesn't make sense.. until you factor dollars in... today's manufacturers factor cost more than anything. If they can get away from putting in another row of bunks... they will do it. Boats on trailers spend more of their life laying on the bunks than they do in water... even here in California where it doesn't freeze. Only blowboaters in the marina.. or really large boats don't have a trailer.. then you have to deal with barnacles and underwater care. There are some offshore boats in Marina Del Rey that are on hydro hoists... and those are just floating trailers.
#22
Registered
Thread Starter
Maybe it is a holdover from long ago. My 88 Myco is designed the same way, except the strake bunks are 4x6 cypress boards on edge, and difficult to align the boat evenly on. That's why the bunks are now angled along the hull under the chines, I'm sure. But, the keel bunks are 2x4's 12 feet long. Maybe, back when all bunks were one solid board, 12' was the longest reasonable length, an needed to be further up on the hull than placing at transom would allow. And that placement is still used today. Either that, or it's a vast conspiracy started by space aliens in cahoots with the government of Atlantis for purposses we don't yet know. Elvis is somehow involved in it;.
#24
Platinum Member
Platinum Member
Here is a Myco with Drive guards good trailers will be supported passed the back off the boat this I imagine avoids developing a hook in your bottom that can rob of a lot of speed.
Funny thing is i have yet to see a rack storage place that has supports that goes all the way passed the rear bulkhead, most of them are way short submitting the hulls to the same stress.
Funny thing is i have yet to see a rack storage place that has supports that goes all the way passed the rear bulkhead, most of them are way short submitting the hulls to the same stress.
Last edited by GLH; 02-17-2004 at 07:43 PM.
#25
I think that if there were 6 bunks, they would have to be all dead nuts on location and height in order to prevent any uneven weight supporting distribution.
It is easier to mount 2 outer bunks in location than it is to mount 1 outer bunk and 1 keel bunk. Plus any twisting of the trailer while towing will be less likely applied to the hull. Also, the notched bottom sounds really legite.
Maybe 'Boatme' can chime in since he works for Manning Trailers.
It is easier to mount 2 outer bunks in location than it is to mount 1 outer bunk and 1 keel bunk. Plus any twisting of the trailer while towing will be less likely applied to the hull. Also, the notched bottom sounds really legite.
Maybe 'Boatme' can chime in since he works for Manning Trailers.
__________________
Some people are like Slinkies - Not really good for anything, but they
bring a smile to your face when pushed down the stairs.
Some people are like Slinkies - Not really good for anything, but they
bring a smile to your face when pushed down the stairs.
#26
Charter Member #232
Charter Member
I am not sure if this has been said yet but is it possible that the boat that was sitting on that trailer had a Notched transom? Kind of like a Superboat Tempest.
Jon
Jon
__________________
Put your best foot forward!
Put your best foot forward!
#27
Registered
Join Date: Dec 2003
Location: Los Angeles California
Posts: 8,306
Likes: 0
Received 2 Likes
on
2 Posts
Originally posted by Audiofn
I am not sure if this has been said yet but is it possible that the boat that was sitting on that trailer had a Notched transom? Kind of like a Superboat Tempest.
Jon
I am not sure if this has been said yet but is it possible that the boat that was sitting on that trailer had a Notched transom? Kind of like a Superboat Tempest.
Jon
#28
Registered
Thread Starter
US1: You also might be on to something. Hull distortion near the transom from too high a keel bunk might cause worse handling than no keel support at all. Too high a keel bunk could reduce the deadrise, and even cause the chines to distort in extreme cases.
GLH: That's some gaudy looking barge you pictured there. (Can I have a ride?!! Pretty please?!! Huh, huh?! ) Very interesting point you brought up about rack storage bunks. Most of the ones I've seen were designed for shorter boats than they actually store.
Reed: Go easy on AudioFN, he's been breathing too much fiberglass dust lately, and it's affecting his judgment. He was actually talking about adding a mast to his boat....
GLH: That's some gaudy looking barge you pictured there. (Can I have a ride?!! Pretty please?!! Huh, huh?! ) Very interesting point you brought up about rack storage bunks. Most of the ones I've seen were designed for shorter boats than they actually store.
Reed: Go easy on AudioFN, he's been breathing too much fiberglass dust lately, and it's affecting his judgment. He was actually talking about adding a mast to his boat....
#29
Registered
Thread Starter
Originally posted by Troutly
I have 16 bunks supporting my 382 on a Prestige trailer.
I have 16 bunks supporting my 382 on a Prestige trailer.
Okay, Troutly, we just determined that keel bunks at the transom cause your boat to be worthless. You'd be best off dumping your now distorted boat for any price you could get. (GET BACK BOYS, I'S HERE FIRST) PM me, and I'll help you out of this mess before Mrs. Trout figures out what a mistake you made.
Hey, anyone want to ride in my new 382?
Actually Troutly, thanks for posting that picture. Do the middle bunks at the transom line up with any stingers or supports in the engine compartment?
Last edited by Chart; 02-17-2004 at 10:26 PM.