4150 to 4500 adapter

Reply Subscribe

Thread Tools

05-15-2016, 02:53 PM

#11

Registered

iTrader: (1)

Join Date: Nov 2004

Location: On A Dirt Floor

Posts: 13,543

Likes: 3,887

Received 3,115 Likes on 1,402 Posts

Quote:

Originally Posted by bck

I know this is more about the 3d printer but as comparison we picked up 12-15 hp and improved the entire curve by swapping a 4150 for a 4500 on a 4150 flanged Vic Jr. 2 in. spacer on both.

I move a bunch of these, especially to the guys with big inch small blocks:

05-15-2016, 03:05 PM

#12

Rookie

Registered

Thread Starter

iTrader: (4)

Join Date: Jan 2003

Location: Grand Rapids, MI

Posts: 5,696

Likes: 438

Received 1,206 Likes on 579 Posts

Quote:

Originally Posted by getrdunn

So what are you going to end up running?

At the moment the 4150. The Dominator was on loan. The Dominator appeared to carry more torque throughout the RPM range.

05-15-2016, 03:13 PM

#13

Rookie

Registered

Thread Starter

iTrader: (4)

Join Date: Jan 2003

Location: Grand Rapids, MI

Posts: 5,696

Likes: 438

Received 1,206 Likes on 579 Posts

SB, The 4150 had 1.750" and the inside of the booster was 0.50"
1150's per Holley are 1.830"
.
[ATTACH=CONFIG]555573[/ATTACH]
.
.[ATTACH=CONFIG]555574[/ATTACH]

Attached Thumbnails

4150 to 4500 adapter-20160515_132426_resized.jpg

4150 to 4500 adapter-20160515_132533_resized.jpg

Last edited by Rookie; 05-15-2016 at 03:16 PM.

05-15-2016, 03:20 PM

#14

Rookie

Registered

Thread Starter

iTrader: (4)

Join Date: Jan 2003

Location: Grand Rapids, MI

Posts: 5,696

Likes: 438

Received 1,206 Likes on 579 Posts

Quote:

Originally Posted by bck

I know this is more about the 3d printer but as comparison we picked up 12-15 hp and improved the entire curve by swapping a 4150 for a 4500 on a 4150 flanged Vic Jr. 2 in. spacer on both.

It's all good. Everything is open for discussion. And real information is always good information.

05-15-2016, 04:12 PM

#15

getrdunn

Registered

iTrader: (7)

Join Date: Feb 2009

Location: NW Michigan

Posts: 8,301

Likes: 1,175

Received 1,490 Likes on 805 Posts

Quote:

Originally Posted by SB

I move a bunch of these, especially to the guys with big inch small blocks:

I saw you had these on another thread. How much? Going to need a couple if I end up with sv565 intakes.

05-15-2016, 04:17 PM

#16

bck

Charter Member#568

Charter Member

Join Date: Dec 2000

Location: Western N.Y.

Posts: 2,171

Likes: 5

Received 16 Likes on 14 Posts

Quote:

Originally Posted by SB

I move a bunch of these, especially to the guys with big inch small blocks:

When we swapped to the 4500 style intake we used that style spacer(not adapter). Picked up 5 hp going from no spacer to 1 in. Picked up another 5 hp peak going to 2 in., but not quite as much under the curve. Overall 1 in. was probably best. Will try another combo when they go back on.

__________________
Straight bottoms and flat decks