Offshoreonly.com - Search Results
Offshoreonly.com

Go Back  Offshoreonly.com > Search Forums
Reload this Page >

Search Results

Register
FAQ
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: Batmeat
Showing results 1 to 12 of 12
Search took 0.07 seconds.
Forum: General Q & A
05-30-2023, 07:39 AM
Replies: 15
Views: 1,170
Posted By BillK

The rockers have to be self aligning if there are...

The rockers have to be self aligning if there are no guide plates.

The early Vortec heads were known for the guides being too tight and hanging valves open under heavy load. The Chevy dealer...
Forum: General Q & A
05-26-2023, 06:38 PM
Replies: 15
Views: 1,116
Posted By TomZ

The wiring is pretty simple. You use a fuel pump...

The wiring is pretty simple. You use a fuel pump safety switch (Holley) and wire the start circuit to the om-side of the switch. If there’s no oil pressure, the fuel pump is not on unless the...
Forum: General Q & A
05-25-2023, 06:19 PM
Replies: 9
Views: 632
Posted By Smitty275

Your carbs are not to big. You have to set the...

Your carbs are not to big.
You have to set the idle with the engines fully warmed up. Best away is with a diagnostic tachometer. Turn them out until you get the highest idle. Then adjust the idle...
Forum: General Q & A
05-12-2023, 09:43 AM
Replies: 18
Views: 1,991
Posted By TomZ

Nothing bolts to it - the y-pipe is bolted to the...

Nothing bolts to it - the y-pipe is bolted to the bottom half of the transom plate. But it's really in the way if you're trying to work around the back of the engine. You'll be happy to have it gone.
Forum: General Q & A
05-05-2023, 06:45 PM
Replies: 3
Views: 514
Posted By F-2 Speedy

thermostat housing........cross over sits in...

thermostat housing........cross over sits in place of the water pump
Forum: General Q & A
04-30-2023, 09:47 PM
Replies: 22
Views: 2,212
Posted By sutphen 30

you need a new flywheel that doesn't have the...

you need a new flywheel that doesn't have the extra weight added to it.its in the form of a large casting bump out from the outer edge.
Forum: General Q & A
04-26-2023, 10:05 AM
Replies: 10
Views: 1,274
Posted By TomZ

If the damage wasn't disclosed, I would make the...

If the damage wasn't disclosed, I would make the seller take those back.
Forum: Do It Yourself, Boating on a Budget
04-17-2023, 02:51 PM
Replies: 4
Views: 1,238
Posted By Griff

Looks normal to me. If there was water intrusion,...

Looks normal to me. If there was water intrusion, I think you'd have some rust color
Forum: Do It Yourself, Boating on a Budget
09-27-2022, 11:32 PM
Replies: 41
Views: 8,962
Posted By zz28zz

I've pulled my 454's a few times and always by...

I've pulled my 454's a few times and always by myself. I have racing mounts, so it may be a bit easier for me to move eng fwd initially. Looks like you had everything major disconnected. Maybe it was...
Forum: Do It Yourself, Boating on a Budget
09-26-2022, 10:48 PM
Replies: 41
Views: 8,962
Posted By Trash

I think you are missing the two rear bolts that...

I think you are missing the two rear bolts that mount on the transom assembly and go through the bell housing attachment points. Make sure the outdrive is off and the outdrive shaft is completely...
Forum: General Q & A
09-04-2022, 09:10 PM
Replies: 52
Views: 5,768
Posted By sutphen 30

-how fast do you need a cam?I have 502 mpi's...

-how fast do you need a cam?I have 502 mpi's sitting in my garage.I'm changing cams so these will be available.just need to know how fast you need it.

Bill
Forum: General Q & A
07-25-2022, 10:36 PM
Replies: 31
Views: 3,923
Posted By phragle

Your going to be this loud.......

Your going to be this loud.... https://www.youtube.com/watch?v=1s52ZXhZS1g
Showing results 1 to 12 of 12


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.