Offshoreonly.com - Search Results
Offshoreonly.com

Go Back  Offshoreonly.com > Search Forums
Reload this Page >

Search Results

Register
FAQ
Calendar
Today's Posts
Search
Vendor Directory
Notices
 
Page 7 of 7
« First
5
6
7
Search: Posts Made By: FlyFast
Showing results 151 to 165 of 165
Search took 0.01 seconds; generated 64 minute(s) ago.
Forum: General Q & A
05-12-2002, 01:13 PM
Replies: 2
Views: 1,500
Posted By FlyFast

I finally got my fuel line right

I was finally able to bend a good solid a solid fuel line. With the right tools and a workable line it was pretty easy. I ended up using a snap on flaring tool and bender with an 90 elbow from...
Forum: General Q & A
05-07-2002, 04:05 PM
Replies: 7
Views: 1,292
Posted By FlyFast

Are the ss braided lines ok with the coast guard...

Are the ss braided lines ok with the coast guard for fuel?
Forum: General Q & A
05-06-2002, 04:02 PM
Replies: 8
Views: 1,558
Posted By FlyFast

I called edelbrock tech line 800 416 8628. You...

I called edelbrock tech line 800 416 8628. You are right they are to release the steam. Edelbrock said to run lines to the front of the intake manifold. If you cannot do that the next best thing...
Forum: General Q & A
05-05-2002, 08:26 PM
Replies: 5
Views: 966
Posted By FlyFast

What type of wet guage guage did you use? My...

What type of wet guage guage did you use? My high volume oil pump runs a normal pressure but the pressure will fall after bringing the throttle back and then bounce back. I think that the sender...
Forum: General Q & A
05-05-2002, 08:20 PM
Replies: 8
Views: 1,558
Posted By FlyFast

US1 I have those holes plugged in my intake....

US1

I have those holes plugged in my intake. could I tee my bypass line from the water pump to the intake and run lines into the back of the intake? Would that give me proper flow? How are they...
Forum: General Q & A
05-03-2002, 10:59 PM
Replies: 0
Views: 1,251
Posted By FlyFast

Ran the boat today with the new closed cooling system

Ran the boat today with the new full closed cooling system. the system seems to work well.

I was running a 1 1/4 thru fitting with a bravo raw water pump and I was seeing over 30 psi of water...
Forum: General Q & A
05-03-2002, 09:55 PM
Replies: 3
Views: 1,770
Posted By FlyFast

F3lS, I have a federal mogual high volume...

F3lS,

I have a federal mogual high volume oil pump on my sbc. I think to get a real reading you need a mechanical guage. My electric guage is 20 at idle and 40 from 2000 rpm up. The pressure...
Forum: General Q & A
05-03-2002, 09:49 PM
Replies: 9
Views: 1,349
Posted By FlyFast

"Bad-Habit" I have a 355 with an edelbrock...

"Bad-Habit"

I have a 355 with an edelbrock 600,vortec heads and an edelbrock air gap intake. I still have my stock merc cam. The factory settings have been the best that I can find for my...
Forum: General Q & A
04-30-2002, 06:37 PM
Replies: 3
Views: 1,385
Posted By FlyFast

I need to run the boat before I will know how the...

I need to run the boat before I will know how the system works. All the parts looked first class except for the riser gaskets.

The bad gaskets I have used before. They are the noname gray...
Forum: General Q & A
04-30-2002, 03:01 PM
Replies: 3
Views: 1,385
Posted By FlyFast

Recall on riser gaskets

There are some bad riser gaskets out there. My boat has been running good. I was concerned about excessive raw water pressure and corrision so I went to closed cooling. The gaskets that came with...
Forum: General Q & A
04-29-2002, 07:19 PM
Replies: 16
Views: 3,827
Posted By FlyFast

The last time I did mine I tried permatex...

The last time I did mine I tried permatex hylomar. I don't know how this will work out. Hylomar (I think that is how it is spelled) was made by rolls royce to seal their jet motors. It is a non...
Forum: General Q & A
04-29-2002, 01:38 AM
Replies: 18
Views: 13,764
Posted By FlyFast

jdelo, I am sorry to hear about your engine....

jdelo,

I am sorry to hear about your engine. I had my engine rebuilt by two different builders in phoenix and I was dissapointed with both shops. The best boat shop I know of will only put in...
Forum: General Q & A
04-23-2002, 12:47 AM
Replies: 29
Views: 4,039
Posted By FlyFast

US1 Fountain, I always appreciated your...

US1 Fountain,

I always appreciated your help. I wish I could help you out on this one. I too used the fel pro gaskets and never had a problem. I did cheat though and I didn't do the retorque...
Forum: General Q & A
04-15-2002, 01:42 AM
Replies: 5
Views: 9,702
Posted By FlyFast

8 works good on my 96 vortec 350 with a edelbrock...

8 works good on my 96 vortec 350 with a edelbrock air gap and a 600cfm carb, stock merc cam and stock merc ignitiion.
Forum: General Q & A
03-24-2002, 10:02 PM
Replies: 16
Views: 7,407
Posted By FlyFast

I took my boat out last wednesday. 1st time this...

I took my boat out last wednesday. 1st time this year. The motor is running great.

edelbrock vortec RPM air gap intake
600 cfm edelbrock 4 barrel carb
Vortec cast iron heads designed by...
Showing results 151 to 165 of 165
 
Page 7 of 7
« First
5
6
7


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.