Offshoreonly.com - Search Results
Offshoreonly.com

Go Back  Offshoreonly.com > Search Forums
Reload this Page >

Search Results

Register
FAQ
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: Illusive
Showing results 1 to 14 of 14
Search took 0.00 seconds; generated 75 minute(s) ago.
Forum: Drives and Lower Units
02-12-2008, 05:41 AM
Replies: 7
Views: 1,275
Posted By Illusive

Had 15 x 26 Bravo 1"s and hitting limiter at...

Had 15 x 26 Bravo 1"s and hitting limiter at 5200rpm, Went with 15 1/2 x 25 P5X's, brought my rpm down to 5000.
Forum: Drives and Lower Units
02-07-2008, 10:08 AM
Replies: 7
Views: 1,275
Posted By Illusive

Before you go through the spacer work, give some...

Before you go through the spacer work, give some hydromotive P5X props a try. I had my drives relocated up 2" in X dim. With the stock Bravo 4 blades I had some cavitation when getting on plane and...
Forum: Wanted
10-31-2007, 04:47 PM
Replies: 9
Views: 1,729
Posted By Illusive

Thought I would drop you a note just in case...I...

Thought I would drop you a note just in case...I have a used set of Bennett Sport Tabs, 12 x 16 with all the cylinders, wiring and pump in good condition. In case you want to repair what you have.
Forum: Drives and Lower Units
08-25-2007, 07:53 PM
Replies: 4
Views: 1,156
Posted By Illusive

When you say hard to shift from F to R, be more...

When you say hard to shift from F to R, be more specific...is it difficult to pull out of gear or difficult into gear. This info helps to get closer to cause.:chimp:
Forum: Drives and Lower Units
07-09-2007, 09:11 PM
Replies: 10
Views: 12,483
Posted By Illusive

My drama continues. I disassembled upper,...

My drama continues. I disassembled upper, couldn't find anything wrong; gears, clutch, springs, bearing looked remarkebly good....but went ahead and flipped the clutch around to see if it would make...
Forum: Drives and Lower Units
06-22-2007, 12:30 PM
Replies: 10
Views: 12,483
Posted By Illusive

Thanks to all for your inputs. I am going to...

Thanks to all for your inputs. I am going to take apart and see if I can find unusual wear on clutch/gear surface.
Forum: Prop Talk
06-19-2007, 10:31 PM
Replies: 5
Views: 847
Posted By Illusive

I'm with the Hydro 30 suggestion...but try the...

I'm with the Hydro 30 suggestion...but try the "X" if you'd like to carry the bow more.
Forum: Prop Talk
06-19-2007, 10:22 PM
Replies: 7
Views: 1,001
Posted By Illusive

OK, assuming Bravo 1's are not blowing out during...

OK, assuming Bravo 1's are not blowing out during acceleration(if they are, blows my theory), my solid guess is your X dimension may be too low and consequently your drives are lifting the stern too...
Forum: Drives and Lower Units
06-19-2007, 10:12 PM
Replies: 10
Views: 12,483
Posted By Illusive

JaayTeee & D*ck, Thanks for the input. My...

JaayTeee & D*ck,
Thanks for the input. My concern with A3 gear set is; am I wasting my $'s because the gears won't work with my unit. D*ck, appreciate the offer to call...I will try to reach out...
Forum: General Q & A
06-18-2007, 10:08 PM
Replies: 103
Views: 100,334
Posted By Illusive

I want to throw my two cents in. I have 1995 454...

I want to throw my two cents in. I have 1995 454 mag mpi's w/VST and fuel pump/sea water combo. It's suspicious that both your engines stalled same time...but I do want all to know for future...
Forum: Drives and Lower Units
06-18-2007, 07:05 PM
Replies: 10
Views: 12,483
Posted By Illusive

I noticed this when I reviewed part #'s, that's...

I noticed this when I reviewed part #'s, that's what caused me concern....that they are including these additional parts because they are needed with my year drive to make the new gears/clutch...
Forum: Drives and Lower Units
06-18-2007, 04:02 PM
Replies: 10
Views: 12,483
Posted By Illusive

Bravo 1 upper gears

I am needing to replace upper gears and clutch on my 1995 Bravo 1. When looking up parts I found there were differences based on outdrive serial #. My serial # is OF493007. My question/concern is...
Forum: Drives and Lower Units
06-14-2007, 10:08 PM
Replies: 13
Views: 7,918
Posted By Illusive

JaayTeee is right on with my experience.

JaayTeee is right on with my experience.
Forum: Drives and Lower Units
06-14-2007, 01:10 PM
Replies: 13
Views: 7,918
Posted By Illusive

Always think about where the clean water is, this...

Always think about where the clean water is, this is where the prop blade will take the strongest bite. Turning props in will help carry the bow, turning out will increase stern lift.
Showing results 1 to 14 of 14


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.