Offshoreonly.com - Search Results
Offshoreonly.com

Go Back  Offshoreonly.com > Search Forums
Reload this Page >

Search Results

Register
FAQ
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: aj1101
Showing results 1 to 8 of 8
Search took 0.00 seconds; generated 97 minute(s) ago.
Forum: General Q & A
05-22-2010, 06:52 AM
Replies: 3
Views: 1,662
Posted By aj1101

Thanks. I am seriously considering going to the...

Thanks. I am seriously considering going to the rev marine set up. My boat is in the water for a good part of the summer, its old and tired so its okay... If I go the rev marine set up I would...
Forum: General Q & A
05-21-2010, 06:22 PM
Replies: 3
Views: 1,662
Posted By aj1101

Question about cast iron exhaust and changing risers

Have a standard merc wet exhaust set up with cast iron manifolds and risers exiting through transom. Had a problem last year with gasket leak and am considering replacing cast iron riser with...
Forum: Do It Yourself, Boating on a Budget
10-22-2009, 06:42 PM
Replies: 18
Views: 12,256
Posted By aj1101

Phil, Can you share a little information on...

Phil,

Can you share a little information on your setup? I have an 86 Scarb 22' with a 300 horse vortec 5.7 liter crate motor. We have to pull the motor because we are having an oil pressure...
Forum: General Q & A
10-10-2009, 03:33 PM
Replies: 13
Views: 1,641
Posted By aj1101

Why wouldn't an exhaust upgrade help? If he is...

Why wouldn't an exhaust upgrade help? If he is running a wet exhaust with the standard cast iron riser exhaust wouldnt an imco or similar exhaust system give him 10-20 hp and more torque? I have a...
Forum: Do It Yourself, Boating on a Budget
09-22-2009, 06:14 AM
Replies: 5
Views: 10,690
Posted By aj1101

Thanks Alan. I appreciate the answer and...

Thanks Alan. I appreciate the answer and insight. I have been doing some reading and it is becoming a little clearer. I would almost just replace the cam and hope for the best but want to try and...
Forum: Do It Yourself, Boating on a Budget
09-18-2009, 06:09 AM
Replies: 5
Views: 10,690
Posted By aj1101

question about determining cam specs

Alan,

Can you point me to an article or write up on how to determine a cam's specs. I have a 350 and think I may have a problem with either my cam or its bearings. I wold like to get an idea of...
Forum: General Q & A
09-05-2008, 02:53 PM
Replies: 15
Views: 2,089
Posted By aj1101

I know that this sounds off but I had a similar...

I know that this sounds off but I had a similar problem last year with my Alpha set up. I could see some water coming in from the transom and I thought from my drive. It took me a while to figure...
Forum: Drives and Lower Units
08-28-2008, 01:33 PM
Replies: 7
Views: 1,187
Posted By aj1101

I have a question about adjusting the spring...

I have a question about adjusting the spring tension on the shifter bracket. I noticed that mine is not moving/rocking when shifting in and out of gear. Can you point me to a discussion of how to...
Showing results 1 to 8 of 8


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.