WTB Transom Rings
#2
Hurley
Gold Member
Join Date: Jan 2004
Location: Ventura, CA
Posts: 354
Likes: 0
Received 0 Likes
on
0 Posts
These are hard to find. I'm looking for the same thing. Would be nice to have new rings and gaskets but I would settle for just new rubbers. Good luck! If I find a source, I'll post again.
Rob...
Rob...
Last edited by hurleyr; 04-24-2008 at 11:10 PM.
#4
Hurley
Gold Member
Join Date: Jan 2004
Location: Ventura, CA
Posts: 354
Likes: 0
Received 0 Likes
on
0 Posts
Where getting warmer. The gaskets I need are 4-1/2 ID x 7-1/2 OD by 3/8" thick.
Rings are 5-1/2 ID x 7-1/2 OD. Hey Scott - Are these the same ones you're looking for?
By the look of my currently burned gaskets the new ones need to be heat/flame resistant.
CP's catalog doesn't show these sizes. I'll give them a call to verify. Thanks for the info.
Rings are 5-1/2 ID x 7-1/2 OD. Hey Scott - Are these the same ones you're looking for?
By the look of my currently burned gaskets the new ones need to be heat/flame resistant.
CP's catalog doesn't show these sizes. I'll give them a call to verify. Thanks for the info.
Last edited by hurleyr; 04-25-2008 at 09:32 AM.
#6
Hurley
Gold Member
Join Date: Jan 2004
Location: Ventura, CA
Posts: 354
Likes: 0
Received 0 Likes
on
0 Posts
I found a company in LA area that cuts custom rubber pieces. They quoted me $37 ea. for the gaskets made from viton (sp?). I Guess this stuff is the cats meow for flame resistance. About 5 time the cost of silicone rubber. My only concern is that I have 3/8 thick gaskets and they only have 1/4".
Scott, How thick are your existing gaskets?
And, did you find a hook up?
Scott, How thick are your existing gaskets?
And, did you find a hook up?
#7
Platinum Member
Platinum Member
Thread Starter
I found a company in LA area that cuts custom rubber pieces. They quoted me $37 ea. for the gaskets made from viton (sp?). I Guess this stuff is the cats meow for flame resistance. About 5 time the cost of silicone rubber. My only concern is that I have 3/8 thick gaskets and they only have 1/4".
Scott, How thick are your existing gaskets?
And, did you find a hook up?
Scott, How thick are your existing gaskets?
And, did you find a hook up?
#8
Hurley
Gold Member
Join Date: Jan 2004
Location: Ventura, CA
Posts: 354
Likes: 0
Received 0 Likes
on
0 Posts
I guess I can't go wrong with 1/4" then.
If you don't mind me asking is he making the same rings as shown above. If so how much?
My rings will polish up. Was thinking about puting them on the inside as well.
If you don't mind me asking is he making the same rings as shown above. If so how much?
My rings will polish up. Was thinking about puting them on the inside as well.
#9
Registered
ALL SEASONS MARINE, got me some really, that I thought came from Imco.They opened up my trim rings and polished them, and made me gaskets. Give them a call, 1-702-293-4499, they are great guys.
Last edited by Nykamp; 05-03-2008 at 06:00 AM. Reason: more info
Thread
Thread Starter
Forum
Replies
Last Post
Double R Performance
Nor-Tech
1
08-02-2006 11:34 AM