25 Outlaw Whipple Merc 525 EFI
05-11-2017 | 07:58 PM
#151
Thread Starter
Registered
Joined: Sep 2013
Posts: 2,320
Likes: 1,040
From: Wisconsin
Think I have the water pump in figured out. Not pretty for the time being but until I find a decent SS street elbow the galvanized will have to do. The galvanized elbow does fit just about perfectly though
[ATTACH=CONFIG]567339[/ATTACH]
[ATTACH=CONFIG]567337[/ATTACH]
Sea strainer will go somewhere in this area. Need diamond plate pieces before I make mount the strainer though
[ATTACH=CONFIG]567338[/ATTACH]
We're getting closer
[ATTACH=CONFIG]567339[/ATTACH]
[ATTACH=CONFIG]567337[/ATTACH]
Sea strainer will go somewhere in this area. Need diamond plate pieces before I make mount the strainer though
[ATTACH=CONFIG]567338[/ATTACH]
We're getting closer
05-12-2017 | 06:26 PM
#155
Thread Starter
Registered
Joined: Sep 2013
Posts: 2,320
Likes: 1,040
From: Wisconsin
Thanks pro27. I've admired your setup for awhile now. Didn't plan on going with this much motor but one happened to be for sale when I was looking. I wish I could've gone with the scx-4 but then I probably would have to redo the transom to get it high enough.
05-14-2017 | 06:00 AM
#156
Thread Starter
Registered
Joined: Sep 2013
Posts: 2,320
Likes: 1,040
From: Wisconsin
Dash panel done. Going to run the Simrad only with the smartcraft and see how I like it. If I feel I need some analog gauges I can add them.
[ATTACH=CONFIG]567399[/ATTACH]
[ATTACH=CONFIG]567400[/ATTACH]
[ATTACH=CONFIG]567401[/ATTACH]
Had to cover the back of the glove box and overlap where the front wraps around. Easy to see it's vinyl but it'll do for now at least.
[ATTACH=CONFIG]567402[/ATTACH]
[ATTACH=CONFIG]567403[/ATTACH]
[ATTACH=CONFIG]567399[/ATTACH]
[ATTACH=CONFIG]567400[/ATTACH]
[ATTACH=CONFIG]567401[/ATTACH]
Had to cover the back of the glove box and overlap where the front wraps around. Easy to see it's vinyl but it'll do for now at least.
[ATTACH=CONFIG]567402[/ATTACH]
[ATTACH=CONFIG]567403[/ATTACH]
05-14-2017 | 10:26 AM
#157
Registered
Joined: Oct 2008
Posts: 1,689
Likes: 115
From: Slidell, La.
Dash panel done. Going to run the Simrad only with the smartcraft and see how I like it. If I feel I need some analog gauges I can add them.
[ATTACH=CONFIG]567399[/ATTACH]
[ATTACH=CONFIG]567400[/ATTACH]
[ATTACH=CONFIG]567401[/ATTACH]
Had to cover the back of the glove box and overlap where the front wraps around. Easy to see it's vinyl but it'll do for now at least.
[ATTACH=CONFIG]567402[/ATTACH]
[ATTACH=CONFIG]567403[/ATTACH]
[ATTACH=CONFIG]567399[/ATTACH]
[ATTACH=CONFIG]567400[/ATTACH]
[ATTACH=CONFIG]567401[/ATTACH]
Had to cover the back of the glove box and overlap where the front wraps around. Easy to see it's vinyl but it'll do for now at least.
[ATTACH=CONFIG]567402[/ATTACH]
[ATTACH=CONFIG]567403[/ATTACH]
looks good!
[ATTACH=CONFIG]567414[/ATTACH]
And cut out a Baja logo on wifes machine!
05-14-2017 | 08:12 PM
#158
Thread Starter
Registered
Joined: Sep 2013
Posts: 2,320
Likes: 1,040
From: Wisconsin
[ATTACH=CONFIG]567422[/ATTACH]
The blue is actually the exact same graphic on the back of the boat pulled off a picture. I think I use that vinyl cutter more than her
Do you have a picture of the back of your glove box?
05-15-2017 | 11:56 PM
#159
Registered
Joined: Oct 2008
Posts: 1,689
Likes: 115
From: Slidell, La.
Her machine is Silouette cutter. I do not have a pic of back,,, its not covered in vinyl, just plain stock white. There is no overlap. Since your vinyl is dark, paint the edge dark to match vinyl and just trim the vinyl on the top edge with a razor. Yours looks good too! Who opens it anyway!
