Offshoreonly.com - Search Results
Offshoreonly.com

Go Back  Offshoreonly.com > Search Forums
Reload this Page >

Search Results

Register
FAQ
Calendar
Today's Posts
Search
Vendor Directory
Notices
 
Page 1 of 2
1
2
Search: Posts Made By: zx1421
Showing results 1 to 25 of 44
Search took 0.01 seconds.
Forum: Drives and Lower Units
10-08-2018, 11:43 AM
Replies: 47
Views: 10,253
Posted By zx1421

https://cimg6.ibsrv.net/gimg/www.offshoreonly.com-...

https://cimg6.ibsrv.net/gimg/www.offshoreonly.com-vbulletin/1500x2000/16f6fd0e_e767_40cc_9a59_997b6ce8fd9f_2b670e9308a5d0c9382dbebcdcfaa4159e2c474c.jpeg

*

It took a couple of weekends, but,...
Forum: Drives and Lower Units
09-21-2018, 07:30 AM
Replies: 47
Views: 10,253
Posted By zx1421

This should help upper gear wear

https://cimg4.ibsrv.net/gimg/www.offshoreonly.com-vbulletin/2000x1493/a649c6da_7acd_482d_a202_6876467288dd_6a81f78a7e59e9be32821889465ae5f94dd8d8d1.jpeg
Forum: Drives and Lower Units
09-17-2018, 01:56 PM
Replies: 47
Views: 10,253
Posted By zx1421

Correction

CORRECTION
upper gearset looked ok and where reused.
Forum: Drives and Lower Units
09-13-2018, 10:49 PM
Replies: 7
Views: 4,395
Posted By zx1421

i saw Freddy today, picking up my scx upper, the...

i saw Freddy today, picking up my scx upper, the dual really isn’t available yet, very few in production, it will be about 3 months.
Forum: Drives and Lower Units
09-13-2018, 10:52 AM
Replies: 10
Views: 4,285
Posted By zx1421

thats what Fred at imco was saying, seems it...

thats what Fred at imco was saying, seems it needs a little restriction to load the cooling passages, then the other questions, that hard spray of water inside the helmet doesn’t bother anything,...
Forum: Drives and Lower Units
09-12-2018, 08:51 AM
Replies: 10
Views: 4,285
Posted By zx1421

i know I wouldnt block it off to the upper, just...

i know I wouldnt block it off to the upper, just going into the engine compartment. But like I said, I don’t think the internal cooling passages inside the scx where meant for all the water and...
Forum: Drives and Lower Units
09-12-2018, 07:57 AM
Replies: 8
Views: 1,723
Posted By zx1421

Im about to put a SCX upper on mine, I have thru...

Im about to put a SCX upper on mine, I have thru hull water pickups, what should I do with the water going to the engine, in the xr I had it blocked and ported out the side, the SCX not sure what to...
Forum: Drives and Lower Units
09-12-2018, 07:37 AM
Replies: 10
Views: 4,285
Posted By zx1421

SCX with through hull water pickups

Any of you folks running a IMCO SCX, but have thru hull pickups? How are you dealing with the water through the SCX case? On my XR I had it blocked off to the gimbal, but a 1/2" hole drilled in the...
Forum: Drives and Lower Units
09-11-2018, 01:16 PM
Replies: 47
Views: 10,253
Posted By zx1421

Nop

Nop
Forum: Drives and Lower Units
09-11-2018, 07:15 AM
Replies: 47
Views: 10,253
Posted By zx1421

yes, I turned the motor off to stop the grinding...

yes, I turned the motor off to stop the grinding in the drive
Forum: Drives and Lower Units
09-11-2018, 07:06 AM
Replies: 47
Views: 10,253
Posted By zx1421

motor is fine, I hope, I should r&r the coupler...

motor is fine, I hope, I should r&r the coupler though
Forum: Drives and Lower Units
09-10-2018, 08:38 PM
Replies: 47
Views: 10,253
Posted By zx1421

It’s...

It’s...
Forum: Drives and Lower Units
09-10-2018, 08:17 PM
Replies: 47
Views: 10,253
Posted By zx1421

https://cimg3.ibsrv.net/gimg/www.offshoreonly.com-...

https://cimg3.ibsrv.net/gimg/www.offshoreonly.com-vbulletin/2000x1504/b41c3786_237e_42f5_b282_6d9ab327cb10_f1db5338bc53a3bef342a2e3d8c8759b08e10d94.jpeg

Bigger slide hammer you say
Forum: Drives and Lower Units
09-09-2018, 02:16 PM
Replies: 47
Views: 10,253
Posted By zx1421

Thank You! That worked, I rotated the vertical...

Thank You! That worked, I rotated the vertical shaft 10 times, prop shaft turned a bit more than 8 3/4, I’ll call that 8.82. So it is what it was a few years back when I checked it all together,...
Forum: Drives and Lower Units
09-09-2018, 12:53 PM
Replies: 47
Views: 10,253
Posted By zx1421

I guess what nobody is saying is, since the upper...

I guess what nobody is saying is, since the upper is not 1:1 , you can’t figuer out gear ratio by turning the vertical shaft in the lower and count rotations, you need it together as a unit and turn...
Forum: Drives and Lower Units
09-09-2018, 07:10 AM
Replies: 47
Views: 10,253
Posted By zx1421

Well, since I’m not opening it, I can only count...

Well, since I’m not opening it, I can only count rotations, on a differential, this would be the procedure. Since you say the upper is 16/19, it’s not 1:1, but darn close.
Forum: Drives and Lower Units
09-09-2018, 07:08 AM
Replies: 47
Views: 10,253
Posted By zx1421

Well, since I’m not opening it, I can only count...

Well, since I’m not opening it, I can only count rotations, on a differential, this would be the procedure. Since you say the upper is 16/19, it’s not 1:1, but darn close.
Forum: Drives and Lower Units
09-08-2018, 07:10 PM
Replies: 47
Views: 10,253
Posted By zx1421

Just to check I’m not crazy. Since I have the...

Just to check I’m not crazy. Since I have the lower off, if I rotate it and the prop shaft turns 1 revolution, and the shaft that goes up in the upper rotates 1 and almost 1/4, that means I have 1:24...
Forum: Drives and Lower Units
09-08-2018, 12:34 PM
Replies: 47
Views: 10,253
Posted By zx1421

Update

https://cimg0.ibsrv.net/gimg/www.offshoreonly.com-vbulletin/2000x1493/e5d8c482_c48d_46c4_9510_379e3d48bbef_fd1c91db8b0cd0e568f52b69e15a534dfa49f0de.jpeg...
Forum: Drives and Lower Units
09-04-2018, 08:12 PM
Replies: 47
Views: 10,253
Posted By zx1421

Max Machine Worx bores out the case and installes...

Max Machine Worx bores out the case and installes thier steel tower, and suggested thier top cap, that has a steel insert for the bearing to ride on. I already have thier clutch shaft. I think none...
Forum: Drives and Lower Units
09-04-2018, 06:47 PM
Replies: 47
Views: 10,253
Posted By zx1421

thank you for drawing this up for me. I spoke to...

thank you for drawing this up for me. I spoke to Aaron at Max Machine, they made a tool to yank it out, modded slide hammer, so I’m going to stop messing with it. I think I’m goig to go with a...
Forum: Drives and Lower Units
09-04-2018, 08:45 AM
Replies: 47
Views: 10,253
Posted By zx1421

thank you, your drawing is right on, I’ve...

thank you,
your drawing is right on, I’ve invisioned in my head the same idea, i haven’t pulled the pinion nut yet, I did put the bell housing pins back in, so I can put pry bar under pinion gear,...
Forum: Drives and Lower Units
09-04-2018, 05:52 AM
Replies: 47
Views: 10,253
Posted By zx1421

yes the bell housing moves freely up down left...

yes the bell housing moves freely up down left and right. I pulled the pivot pins and thought maybe I could just sacrifice the bellows, the bellhousung will go in and out but, the shaft stays solid...
Forum: Drives and Lower Units
09-03-2018, 10:07 PM
Replies: 8
Views: 1,723
Posted By zx1421

I’m running a XR its that has that extentsion...

I’m running a XR its that has that extentsion box. I fun a -2” imco shorty, I’m even with the sponsons. I run a teague Quadrotor, i porpoise at 70-80 on smooth water, give me a bit of chop, and all...
Forum: Drives and Lower Units
09-03-2018, 11:47 AM
Replies: 47
Views: 10,253
Posted By zx1421

thats what I’m afraid of. Is it stuck in the...

thats what I’m afraid of. Is it stuck in the bearing or the coupler, if you go in the boat you can see the 2 o rings on the shaft that are usually on each side of the bearing
Showing results 1 to 25 of 44
 
Page 1 of 2
1
2


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.