Offshoreonly.com - Search Results

Go Back  Offshoreonly.com > Search Forums
Reload this Page >

Search Results

Notices
Search: Posts Made By: Johnb
Showing results 1 to 12 of 12
Search took 0.01 seconds.
01-25-2013, 10:02 AM
Replies: 70
Views: 14,002
Posted By Johnb

And Concluding for Mike T- Tom did switch...

And Concluding for Mike T-

Tom did switch back to a Hi-Helix 14:71. True statement. However he switched back because of the issues he had with the EFI. In both of our cases if we had set up our...
01-24-2013, 10:36 AM
Replies: 70
Views: 14,002
Posted By Johnb

Responding to post #18 concerning Mike Tach and a...

Responding to post #18 concerning Mike Tach and a PSI blower.
I did buy a PSI blower and Indy Manifold from Mike.
There were no issues with Mike or the specific components as he sold them and...
Forum: HTM
12-21-2012, 05:29 PM
Replies: 33
Views: 19,751
Posted By Johnb

X-dimensions

Just bought a new hull- totally empty.
Some input on the power:
Donovan 11.1 block- 600inches- 4.5x4.630- 7.5 oliver rods.
Crower crank- Olds mains, Olds center thrust, Chevy seals and rods....
03-15-2012, 06:45 PM
Replies: 31
Views: 11,544
Posted By Johnb

COLOR="SeaGreen"]The dyno sheet provided by the...

COLOR="SeaGreen"]The dyno sheet provided by the builder states; peak torque at 4900 rpm – 611.4 HP - 654 torque – fuel pressure 4.967 Psi; peak HP at 5900 rpm – 670.3 HP – 595.5 torque – fuel...
03-14-2012, 01:52 PM
Replies: 31
Views: 11,544
Posted By Johnb

Brad: Just because someone talks more than...

Brad:

Just because someone talks more than they should--- doesn't mean they have much to say.
03-14-2012, 01:35 PM
Replies: 31
Views: 11,544
Posted By Johnb

This note below is the Federal Mogul response...

This note below is the Federal Mogul response (owner of Carter Fuel Systems) concerning the part number supplied.

With that information this pump will support:
500hp @ a BSBC of .5
450hp @ a...
03-14-2012, 11:45 AM
Replies: 31
Views: 11,544
Posted By Johnb

The part number M61045 provided by the builder is...

The part number M61045 provided by the builder is not listed in Summit, Jegs or the Carter web site. The closest part number is M6104. This is a stock replacement pump for a 454. The builder should...
Forum: Warlock
10-01-2009, 06:46 PM
Replies: 7
Views: 6,304
Posted By Johnb

Smile I have the same boat you do but an 89...

It is a wild ride at the porpoise point and unfortunately not easily fixed. The boat likes a good wind blown chop, likes to ride on 4 points. I added tunnel extensions (20") tried 7 props (now...
Forum: Warlock
09-25-2009, 04:22 PM
Replies: 147
Views: 136,435
Posted By Johnb

Have one of these with similar power-- what is...

Have one of these with similar power-- what is your drive height and set back??
Gear and prop??
How did you get past the porpoising??
Forum: General Q & A
09-25-2009, 04:17 PM
Replies: 22
Views: 4,506
Posted By Johnb

25 warlock

I have one of these boats and have fought porpoising forever..
I run a 1150hp 540 (AFR 357CNC, matched cam, 14:71 @ 14psi)
34 5 blade (1.5 gear) spinning 6500rpm+... Did not get there over night....
01-25-2007, 06:07 PM
Replies: 6
Views: 4,918
Posted By Johnb

Re: Standoff Box potential improvement yes or no?

Did you change to the Stelling only or make other changes? What did the boat do after your installation??
I know the two boats can't be compared- but do you still have the box??
01-24-2007, 06:51 PM
Replies: 6
Views: 4,918
Posted By Johnb

Question Standoff Box potential improvement yes or no?

Currently running a short XR with sport master case. Turns a Bravo 34"lab at 6000 on a 1.5 gear (117 radar). Prop runs deep with the full bulb in the water at top end. The boat is a 25 ft Warlock...
Showing results 1 to 12 of 12


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.