Offshoreonly.com - Search Results
Offshoreonly.com

Go Back  Offshoreonly.com > Search Forums
Reload this Page >

Search Results

Register
FAQ
Calendar
Today's Posts
Search
Vendor Directory
Notices
 
Page 1 of 13
1
2
3
11
Last »
Search: Posts Made By: Boat1
Showing results 1 to 25 of 319
Search took 0.01 seconds.
Forum: General Q & A
07-06-2011, 09:15 PM
Replies: 7
Views: 4,465
Posted By Boat1

I'd try another set of rocker arms. Just seems...

I'd try another set of rocker arms. Just seems like you have addressed everything else, the contact geometery looks very good.
Forum: General Q & A
07-04-2011, 07:13 PM
Replies: 10
Views: 2,342
Posted By Boat1

The pump volume increases with rpm but the...

The pump volume increases with rpm but the presure should not exceed 7 psi on a stock mechanical fuel pump. Sounds like the pump is wrong or defective.
Forum: General Q & A
07-04-2011, 07:05 PM
Replies: 5
Views: 674
Posted By Boat1

Your describing the plastic threaded tee inlet to...

Your describing the plastic threaded tee inlet to the exhaust manifold. You can remove the exhaust manifold, turn it upside down and clear the threads. The plastic may have failed from improper...
Forum: General Q & A
07-04-2011, 01:00 PM
Replies: 87
Views: 111,315
Posted By Boat1

Did you ever find out why the distributor had the...

Did you ever find out why the distributor had the damage?
Forum: General Q & A
06-26-2011, 07:28 PM
Replies: 3
Views: 1,045
Posted By Boat1

If EFI then 160.

If EFI then 160.
Forum: Do It Yourself, Boating on a Budget
06-26-2011, 07:26 PM
Replies: 6
Views: 1,217
Posted By Boat1

Find the data link connector and see if the...

Find the data link connector and see if the terminals are labeled on the end. Jumper A and B to get the ECM in base timing, then set the timing at 8 deg BTDC. You will likely need to rev the engine...
Forum: Do It Yourself, Boating on a Budget
06-26-2011, 07:18 PM
Replies: 6
Views: 1,770
Posted By Boat1

PM sent.

PM sent.
Forum: Do It Yourself, Boating on a Budget
06-19-2011, 08:41 PM
Replies: 5
Views: 1,106
Posted By Boat1

They should retract so that no silver is showing...

They should retract so that no silver is showing on the shaft. Someone may have installed spacers inside the rams so that the ram travel is limited or you may need to bleed the system of air. Good...
Forum: Swap Shop
06-13-2011, 08:06 PM
Replies: 3
Views: 500
Posted By Boat1

New price $650 for the pair. These have been...

New price $650 for the pair. These have been refinished, balanced, and pitch verified by Performance Props. They are like new. Pictures available.
Forum: Do It Yourself, Boating on a Budget
06-11-2011, 08:53 PM
Replies: 28
Views: 18,809
Posted By Boat1

Since your taking your time contact Bob Madera...

Since your taking your time contact Bob Madera mentioned above. He will really help you and can provide all the parts. Call him, you won't be disappointed.
Forum: General Q & A
06-11-2011, 08:36 PM
Replies: 38
Views: 4,470
Posted By Boat1

When you install a crossover system you should...

When you install a crossover system you should also install a water pressure guage on the block. Your engine water pressure should not exceed 25 psi at WOT, this can be controlled by the bypass size...
Forum: General Q & A
06-11-2011, 08:13 PM
Replies: 21
Views: 4,500
Posted By Boat1

Look at the carburetor boosters on the primary...

Look at the carburetor boosters on the primary side. At idle there should be no visable fuel dripping from the boosters or the accellerator pump squirters. If the needle and seat are bleeding fuel...
Forum: General Q & A
06-11-2011, 08:03 PM
Replies: 1
Views: 650
Posted By Boat1

Please provide a better description of the...

Please provide a better description of the complete system and describe all the hoses going to the thermostat housing. Flow should come from the raw water pump through a fuel cooler then oil/power...
Forum: Swap Shop
06-05-2011, 06:05 PM
Replies: 3
Views: 500
Posted By Boat1

St. Charles, Missouri. I'll split then freight...

St. Charles, Missouri. I'll split then freight if your interested.
Forum: Swap Shop
06-04-2011, 08:10 PM
Replies: 3
Views: 500
Posted By Boat1

Hydromotive Quad IV 21 Pitch Left/Right

Nice pair of Hydromotive Quad IV 21 pitch props. Hubs are for a standard Bravo prop shaft and are not changable. Send email address for pictures. The pair together, $700.00 plus the ride.
Forum: General Boating Discussion
05-28-2011, 07:05 PM
Replies: 42
Views: 12,186
Posted By Boat1

Yes I have a past that that includes poor...

Yes I have a past that that includes poor decisions and bad business decisions. I also acknowledge there is a judgement aginst me that has not been paid. Anyone that can use the search function can...
Forum: Drives and Lower Units
05-25-2011, 07:05 PM
Replies: 10
Views: 14,020
Posted By Boat1

For a quick fix, disconnect the drive cable at...

For a quick fix, disconnect the drive cable at the engine. Manually shift the drive into neutral, find the detent position of the drive. Put the shifter control in neutral, find the detent position...
Forum: General Q & A
05-25-2011, 06:06 PM
Replies: 3
Views: 1,674
Posted By Boat1

That is normal for a hose. Put the boat in the...

That is normal for a hose. Put the boat in the water, they will be cooler.
Forum: Drives and Lower Units
05-25-2011, 11:14 AM
Replies: 11
Views: 4,825
Posted By Boat1

The picture shows your hydraulic manifold block...

The picture shows your hydraulic manifold block to the trim pumps. The two bolts visable hold the plastic cover on, remove those you will find two studs with nuts or bolts. Remove those and the...
Forum: General Q & A
05-25-2011, 11:00 AM
Replies: 20
Views: 2,494
Posted By Boat1

It means the secondary relay is working, that...

It means the secondary relay is working, that sends a 12V signal to the starter mounted solinoid. Also be sure the main battery wires are tight on the starter lug while your beating on it. Good...
Forum: General Q & A
05-25-2011, 08:44 AM
Replies: 20
Views: 2,494
Posted By Boat1

Mercury uses two solenoids in the starter system....

Mercury uses two solenoids in the starter system. The click you are hearing is the secondary solinoid mounted up by the 50 amps re-set circuit breaker. The starter has a solinoid mounted on it that...
Forum: General Q & A
05-25-2011, 08:34 AM
Replies: 87
Views: 111,315
Posted By Boat1

The damage in the distributor is something you...

The damage in the distributor is something you need to figure out. I would look very carefully at all components, pull the shaft from the distributor, inspect the lower and upper bushings in the...
Forum: General Q & A
05-24-2011, 09:17 PM
Replies: 87
Views: 111,315
Posted By Boat1

Pull the distributor, possibly the roll pin has...

Pull the distributor, possibly the roll pin has worked out of the distributor gear, also visually inspect the gear for cracked teeth. Manually spin the distributor and feel for a click. Use a...
Forum: Do It Yourself, Boating on a Budget
05-24-2011, 10:20 AM
Replies: 14
Views: 7,133
Posted By Boat1

Sounds like the nozzle may be pairtially blocked....

Sounds like the nozzle may be pairtially blocked. The phillips screw holds the accelerator pump squirt nozzle to the carb, if you remove the screw you can take the nozzle off and spray it out. ...
Forum: General Q & A
05-24-2011, 10:09 AM
Replies: 15
Views: 2,926
Posted By Boat1

I personally dont rev an engine above 1200 rpm on...

I personally dont rev an engine above 1200 rpm on the hose. You can leave it on the trailer and back it down a ramp, the engine does not need load, but does need rpm for timing advance. Your...
Showing results 1 to 25 of 319
 
Page 1 of 13
1
2
3
11
Last »


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.