Looking Great!
Aluminum head, big tube headers, and...:drink:

Thanks Pat time/patience mostly patience.

I can see how it does get out of hand, especially with the bigger hp. I'm leaning towards new merc 496's, keep it all stock. I doubt I'd be buying any kind of exhaust hardware like that. I'd like to take the apache up to you and Leon to get a better handle on what I can expect to pay for parts on the rigging. Can you guys do a new wiring harness? Sorry for the hijack VV

old cams would be fun, buzzzzzzzzzzzzzzzzzzzzzz:drink:

VV so far who's in the leed with contest??? Just wondering.

All I can say I have a $10,000.00 deposit just for labor to get started. When that runs out they will call me. So anyone that guessed less than that are out unless of course they give me money back. :evilb:

[QUOTE=Velocity Vector;2654917]I'm going to sweeten the thread a little. Tell a friend, Winner gets a $100.00! :ernaehrung004: :food-smiley-007:

Look at the parts listed below: ??? POST>>How much is it going to cost for just the labor turn Key??? Taken out the old and putting in the new :eek: I want you guy's to take an edcuated guess on how much the labor will end up costing on the project, all I can say is it is $95.00 per hr. :grinser010:

To make it fair I'm staying out. When I get the final bill I will post the winner. Good Luck hope you win!
One guess and make it a good'en :rolleyes:

3 Rules:
1. If you go over the total your guess doesn't count!
2. If for some reason there is a tie the earler post will win.
3. Once your $$$ guess is posted you can not edit it. VV

If you make a error in the post let me know and I will change it and re-post it here. All money amounts are in U.S. DOLLARS VV

2 - Mercury Supercat race engines $29,000.00
2 - Weldon 1000 HP Fuel pumps $1,400.00
2 – Regulators w/ by-pass Areomotive $500.00
2 - Oil coolers & brackets $500.00
2 - Keith E. Oil pre-lubers $1,400.00
2 - Hardin Marine water separators $440.00
2 - MSD Marine distributors $780.00
2 - MSD high vibration coils $100.00
2 - MDS coil brackets $10.00
2 - MSD sets rpm chips $132.00
2 - MSD insulated plug wires $200.00
2 - Stellings headers $13,000.00
2 - Stellings tailpipes $5,300.00
2 - Air activated switchable mufflers $2,400.00
1 - Air pump for mufflers $325.00
2 – Hour meter Gauges Livorsi $100.00
2 - Xtreme Billet Aluminum Engine Mounts Rear Side By Side Mount $600.00
2 - Xtreme Billet Aluminum Engine Mounts Front Side By Side Mount $880.00
2 - Billet Aluminum Xtreme MSD 6M-2, Rev Limter & Coil Bracket $270.00
2 - Billet Aluminum Chevy Distributor Hold Down Clamp $80.00
2 - Throttle Bracket King Demon Carburetors $95.00
2 – Wiring harness $278.00


2 - Mercury XR race drives W/ 1" shorties $13,000.00
2 - 15.25 X 34P Mercury Marine props $1,500.00
2 - IMCO 12" Extension boxes $8,000.00
1 - IMCO Tie bars Lower $379.00
2 – IMCO HD gimbal rings and helmets $2,700.00
2 - K-Plane 380 plates $1,800.00
2 - K-plane pumps $500.00
2 - Trim pumps $500.00
4 - Billet 42oz. reserve fluid reservoirs $800.00
2 - Rule 2000 bilge pump $310.00
2 - Dual billet trim reservoirs for pumps Dana Marine $900.00
3 - Billet battery boxes Dana Marine $400.00
2 – XR Drive actuators $548.00
2 – XR drive locks $60.00
2 – Prop Locks $72.00
2 - Harden Marine Sea strainers $2,253.00


1 - Piratecom 5 person intercom system W/extreme headsets $2000.00
1 - VHF Radio $585.00
1 - VHF Remote microphone $160.00
1 - VHF antenna $100.00
1 - Ratchet mount $25.00
1 - VHF radio flush mount $25.00
1 - Go Pro video camera $170.00


Guess list
nada1> 29K
BY U BOY> 26K
Thong Fellow> 24.5K
007joe> 19K
Perlmudder> 18K
niceguy> 17.5K
Pat McPherson> 15.2K
TexomaPowerboater> 16K
DKerns> 13.5K
Slick02> 11K
Andy> 10,735K
jrayan26> 10K
1Hyper1> 9.5
Jigsaw89> 8.9K
Sick Stinger> 3K

Question?
 

It's assumed that they are doing all the mech rigging, but are they doing the electronics, intercom etc as well?

Yes everything in the list including intercom.

I think ExcaliburHawk41 should not be allowed as a contestant:drink: