Offshoreonly.com - Search Results
Offshoreonly.com

Go Back  Offshoreonly.com > Search Forums
Reload this Page >

Search Results

Register
FAQ
Calendar
Today's Posts
Search
Vendor Directory
Notices
 
Page 1 of 5
1
2
3
Last »
Search: Posts Made By: Jb-fse
Showing results 1 to 25 of 113
Search took 0.01 seconds.
Forum: General Q & A
11-17-2010, 03:57 PM
Replies: 32
Views: 14,627
Posted By Jb-fse

Fuel hose

I'm a earls dealer in michigan. The coast guard wants marine fuel hoses to have a fire and permeation rating. This is a USCG type A-1 under deck rating. Stainless braided hose has not been tested by...
Forum: General Boating Discussion
10-15-2010, 10:14 AM
Replies: 12
Views: 2,390
Posted By Jb-fse

Omg

We sell S-X pumps. I have also seen this many times. The customer will blame the blow up on the pump.
Forum: General Boating Discussion
03-22-2010, 02:53 PM
Replies: 15
Views: 2,334
Posted By Jb-fse

Fuel Line Size

With a 715 hp engine you will need a wide open throttle .99 GPM. That is a bunch to try to suck through a 3/8 Inch pick up.
I would look to a gas tank repair company to install a larger bung in the...
Forum: General Q & A
11-17-2009, 08:30 AM
Replies: 5
Views: 1,598
Posted By Jb-fse

Helm Size

we sell the helm that you are using for a twin 28-32 application.
If you want a slower steer ratio use the next size smaller helm.
A 211-1008 (95 cu in rev)
Forum: General Q & A
10-30-2009, 08:25 AM
Replies: 3
Views: 663
Posted By Jb-fse

P/S speed

no changing the hose size will not change the speed. the out put of the helm in cc's controls the speed.
Forum: General Q & A
09-25-2009, 12:58 PM
Replies: 5
Views: 1,202
Posted By Jb-fse

Another source

www.reidwashbon.com
Forum: General Q & A
08-11-2009, 10:41 AM
Replies: 1
Views: 4,080
Posted By Jb-fse

check valves

no ones fuel pump likes to have a check valve in front or suction side. we are a S-X dealer and we put them on the discharge side. we also make a soft seat size #10 an check for this . we have them...
Forum: General Q & A
08-11-2009, 10:35 AM
Replies: 28
Views: 3,980
Posted By Jb-fse

vapor lock

you have to remember that the cause is engine heat and heat soak in the engine bay. try turning on your bilge blower to exhaust extra air and heat. the fix is to keep the bilge cool.
Forum: General Q & A
07-20-2009, 02:44 PM
Replies: 4
Views: 1,421
Posted By Jb-fse

leaking rams

you will not know until you take the ram apart and look at its condition.
Forum: General Q & A
07-20-2009, 10:05 AM
Replies: 4
Views: 1,421
Posted By Jb-fse

leak

the leak you have is from the tab cylinder. if it is not that bad probily leaking from the shaft seals on the cylinder.
Forum: General Boating Discussion
07-20-2009, 10:01 AM
Replies: 4
Views: 795
Posted By Jb-fse

port thread

if the fitting has a o-ring on it . that is a straight thread size #10
that is a 7/8-14 thread. if you screwed in a 1/2-14 npt pipe it will fall out. look at the port that you are threading in to if...
Forum: General Q & A
07-09-2009, 08:56 AM
Replies: 53
Views: 49,903
Posted By Jb-fse

engine bay temps

we have done engine bay temp test for our hose supplier company.the newer boats run very high engine compartment temps do to lack of venting. we have had many people have vapor lock conditions...
Forum: General Q & A
07-08-2009, 08:58 AM
Replies: 53
Views: 49,903
Posted By Jb-fse

p/s cooler

we have had p/s pumps come to us burned up do to no coolers. when we checked the engine bay temp it was well over 500 f under the hatch. remember that the oil in the ram lines does not return to the...
Forum: General Q & A
06-19-2009, 11:43 AM
Replies: 8
Views: 1,273
Posted By Jb-fse

Fittings

The Hose You Have Apears To Be Size #6 (3/8). The Picture Of The Cross Over Hose That You Have Run Shows That Those Lines Will Fail Do To To Tight Of A Bend Radius. We Also Have Thru Hull Stainless...
Forum: Do It Yourself, Boating on a Budget
06-09-2009, 02:29 PM
Replies: 6
Views: 1,308
Posted By Jb-fse

exhaust hose

how much are you looking for and what size.
Forum: General Q & A
05-28-2009, 02:05 PM
Replies: 5
Views: 808
Posted By Jb-fse

This Is Out Of Our Eaton Products Catalog

Atf Type A And Most Petroleum Based Fluids
Forum: General Q & A
05-27-2009, 12:29 PM
Replies: 3
Views: 780
Posted By Jb-fse

he is testing the nascat boat in charlotte n.c.

he is testing the nascat boat in charlotte n.c.
Forum: General Q & A
05-15-2009, 03:01 PM
Replies: 7
Views: 865
Posted By Jb-fse

if you have had tempature swings it is...

if you have had tempature swings it is condensation in the pump. we see it all the time.
Forum: Do It Yourself, Boating on a Budget
04-30-2009, 06:50 PM
Replies: 14
Views: 2,452
Posted By Jb-fse

fuel pressure

BLEFEVER The fuel pump that you have was made by S-X PERFORMANCE for edelbrock.It is the same as a 18205.
This pump is rated for a engine that max h.p. is 480hp.
If you engine is less than that you...
Forum: General Q & A
04-24-2009, 01:37 PM
Replies: 3
Views: 793
Posted By Jb-fse

line position

If you have the helm with the shaft end facing you and ports up the line are as follows. pressure port is at right side rear. tank port is at right side front. left turn port is at left side front...
Forum: General Q & A
04-22-2009, 08:37 AM
Replies: 7
Views: 2,806
Posted By Jb-fse

Hard steering

you did not say what helm you have, is it new or old correct size or to big, a common problem. Is the engine at the correct idle speed, does the belt slip on the pump. When p/s is set up correct you...
Forum: General Q & A
04-17-2009, 03:28 PM
Replies: 4
Views: 911
Posted By Jb-fse

Line Size

Your Line Size Should Be 10mm Or Here In The Us 3/8
Forum: General Boating Discussion
04-17-2009, 01:50 PM
Replies: 14
Views: 1,497
Posted By Jb-fse

Stainless Fittings

I Sell Stainless Fittings And Adaptors, Also Hose Assemblies. Feel Free To Call 586-790-8880 Ext251
Forum: General Q & A
04-03-2009, 09:44 AM
Replies: 4
Views: 972
Posted By Jb-fse

Lines

Give us a call we do hyd steering lines everyday.
fluid systems 586-790-8880
Forum: General Q & A
04-02-2009, 01:21 PM
Replies: 2
Views: 984
Posted By Jb-fse

hose size

#10 looks to be return line from cooler 3/8 #18 looks to be feed line from tank to pump 1/2
Showing results 1 to 25 of 113
 
Page 1 of 5
1
2
3
Last »


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.