Offshoreonly.com - Search Results
Offshoreonly.com

Go Back  Offshoreonly.com > Search Forums
Reload this Page >

Search Results

Register
FAQ
Calendar
Today's Posts
Search
Vendor Directory
Notices
 
Page 1 of 3
1
2
3
Search: Posts Made By: PROFILE
Showing results 1 to 25 of 64
Search took 0.00 seconds.
Forum: General Q & A
05-24-2007, 08:52 PM
Replies: 2
Views: 791
Posted By PROFILE

What sort of ignition problem? No spark? What...

What sort of ignition problem? No spark? What year is the engine? tiller or remote? If it's no spark I'd try dissconnecting the kill switch first. Should be a black wire with a yellow tracer.
Jeff
Forum: General Q & A
05-24-2007, 08:31 PM
Replies: 15
Views: 37,876
Posted By PROFILE

Is it carb or fuel injected? If its a carb motor,...

Is it carb or fuel injected? If its a carb motor, the mikuni carbs have a small fuel filter in them under the fuel pump. I'd say they are probably partially gummed up. You must remove the carbs and...
Forum: General Q & A
09-28-2006, 06:19 AM
Replies: 8
Views: 3,922
Posted By PROFILE

Re: Outdrive Lube Pump

I use a 1 gallon stainless steel garden sprayer from Home depot. I took the spray end off (leaviing the sqeeze handle to control flow) and added a short piece of hose with the threaded fill fitting...
Forum: General Q & A
10-28-2005, 08:50 PM
Replies: 3
Views: 1,041
Posted By PROFILE

Re: Need help with Honda outboard

The junction block is probably the relay box, most jap outboards use a single relay "box" with just terminals sticking out for the wires. The up and down relay are both built into this one unit. Its...
Forum: General Q & A
06-15-2005, 09:28 PM
Replies: 15
Views: 7,275
Posted By PROFILE

Re: Leaving boat in salt water ?

I would'nt leave it in for more than a couple days at a time.
Here in Cape Coral, I've have seen tiny barnacles start to grow in as little as 4 days. Pain to get off.
Forum: General Boating Discussion
06-11-2005, 10:03 PM
Replies: 0
Views: 651
Posted By PROFILE

Speed Racer in Fort Myers

Went to the OSS dry pits today with my son to check out the boats. Saw Speed Racer, that boat is unbelievable. Anyone know anything about it?, Speed?
Forum: General Boating Discussion
06-11-2005, 09:44 PM
Replies: 148
Views: 30,752
Posted By PROFILE

Re: How fast is your V Hull (try to be honest)

72.4 on gps, full tank, 2 people.
1993 29ft Profile, approx 4500lbs.
502 w/ 250 b&m supercharger, stock port iron heads.
Canfield heads and new cam installation underway, hoping for upper 70's...
Forum: General Q & A
06-03-2005, 03:01 PM
Replies: 2
Views: 728
Posted By PROFILE

Re: Boost Cooler?

What do you guys think?
Forum: General Q & A
06-03-2005, 11:41 AM
Replies: 2
Views: 728
Posted By PROFILE

Question Boost Cooler?

Has anyone tried a boost cooler setup from Snow Performance?
Looks pretty interesting, Check it out at: snowperformance.net
Forum: General Q & A
03-28-2005, 08:30 PM
Replies: 1
Views: 1,200
Posted By PROFILE

Re: Alpha impeller replacement

It goes on top of the housing.
Forum: General Q & A
03-24-2005, 09:51 PM
Replies: 3
Views: 3,152
Posted By PROFILE

Re: Crank Case Venting

I posted a question on this subject also. After looking at the parts diagram for the 525 it looks like they use a pcv valve.
Rumrunner advised against this because hot oil being injested into...
Forum: General Q & A
03-24-2005, 08:47 PM
Replies: 6
Views: 7,814
Posted By PROFILE

Re: PCV valve with supercharger

Rummrunner,
Thanks for the reply. My motor blows a little oil out of the valve cover breather after I run it hard (extended periods of boost). I was considering running the pcv valve until I read...
Forum: General Q & A
03-23-2005, 09:21 PM
Replies: 6
Views: 7,814
Posted By PROFILE

PCV valve with supercharger

Anybody running a pcv valve with a roots style supercharger?
It looks like the older merc 525 and 600 sc's used one that in mounted in the back of the intake manifold.
Forum: General Q & A
03-23-2005, 04:36 PM
Replies: 12
Views: 2,693
Posted By PROFILE

Re: Installing pop-up cleats

If the deck where you cut through is wood cored I would resin coat the wood after you cut the hole,before you install the cleat.
Forum: General Q & A
02-25-2005, 09:31 AM
Replies: 14
Views: 2,601
Posted By PROFILE

Re: Verify age of Mercruiser

What are the serial #'s
Forum: General Q & A
02-24-2005, 08:22 PM
Replies: 7
Views: 4,256
Posted By PROFILE

Re: Which Battery Charger

I've installed the guest model for several customers with no problems.
I think as long as you do not leave it on all the time you will not have any battery issues.
Installed one of the "smart leg...
Forum: General Q & A
02-24-2005, 07:31 PM
Replies: 11
Views: 4,810
Posted By PROFILE

Re: Cam experts: reversion question?

Bob,Thanks for the comp sym ,seat to seat tip.
Ok heres the million dollar question,What cam do you recommend,flat tappet hydraulic as well as hyd roller please.
Here as some of my specs:
.030...
Forum: General Q & A
02-24-2005, 05:12 PM
Replies: 11
Views: 4,810
Posted By PROFILE

Re: Cam experts: reversion question?

Bob,
Thanks for replying.Yes thats the cam I have now,but I'm thinking its the cause of my reversion problem.
I would like to make some where around 650hp or better and 5500 wot. Do you think this...
Forum: General Q & A
02-24-2005, 12:11 PM
Replies: 11
Views: 4,810
Posted By PROFILE

Re: Cam experts: reversion question?

KAAMA,I respect your advice.
I picked that cam after comparing it to many different cams using desk top dyno as the comparison tool.It peaked tq=634@3500 and hp=536 @5000.All of the other marine...
Forum: General Q & A
02-24-2005, 07:02 AM
Replies: 11
Views: 4,810
Posted By PROFILE

Question Cam experts: reversion question?

Do you think this cam could have water reversion problems with Gil exhaust,too much duration?
240 int, 253 ex dur @.050
113 lobe sep
575 int, 595 ex lift

I'm running this cam in my...
Forum: General Q & A
02-19-2005, 03:07 PM
Replies: 1
Views: 1,064
Posted By PROFILE

Question Clay Smith Cams

Has anyone had any experience with custom cams from clay smith?
Wondering if I'd be better off letting them custom grind a cam for me vs. an off the shelf cam?
Thanks
Forum: General Q & A
02-16-2005, 06:51 AM
Replies: 0
Views: 780
Posted By PROFILE

Question Cylinder Flow Specs

Does anyone have flow#'s for the Dart iron eagle's(308 runner) and Merlin (iron 320 runner).
thanks
Forum: General Q & A
02-16-2005, 06:28 AM
Replies: 8
Views: 1,341
Posted By PROFILE

Re: Blown 509 head recommendations

Thanks for the replys.
50boat, I'm using cometic gaskets and am not having sealing issues.I'm looking for new head recommendations.
I boat in salt water so if I go aluminum they will need to be...
Forum: General Q & A
02-15-2005, 09:03 PM
Replies: 8
Views: 1,341
Posted By PROFILE

Question Blown 509 head recommendations

I want to upgrade the heads on my engine.
Currently running stock rec ports with inconel exh valves.
Setup now is 509ci,8.75 compression,hyd. flat tappet cam, B&M 250 blower(6lbs boost),Nickerson...
Showing results 1 to 25 of 64
 
Page 1 of 3
1
2
3


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.