Just did a quick walk threw and around the boat. Huge reverse chine for 1. It's a big 36, Gordon and I measured the tip to toe it's 36 to the inch. Good head room on the way into cabin as is say 5'6'' 5'7''. Great lines on it also. Breaking the motors down to
Paint them black and acc going red.

The cabin space is one of the main reasons I bought my 36'.

I do like the lines of a flat deck but I LOVE the cabin on my Warrior.

Cabin suite the needs well. Simple but functional, good head room nice v berth good size couches. On the port side when entering, is that a ice box? Mine is cloth that has 2 exstinquishers in it and a couple flares. Modded for sheriff use or factory?

My cabin has a sink and cooler compartment on the port side when you enter. They designed a fixed box inside the compartment so you can set the cooler into it and it never moves, no matter how rough the seas.

Everything is upholstered and soft, no hard edges. It's very simple and chit don't break or come lose in rough seas! I've verified this countless times. ;-)

I'll get a pic of my set up and post in the next couple weeks. Boat is still in NH behind some snow covered.

Couple pics. Repainted block, redone pulleys and brackets. Oil hoses made along with cooler and thermo filter head mounted
[ATTACH=CONFIG]520367[/ATTACH][ATTACH=CONFIG]520368[/ATTACH][ATTACH=CONFIG]520369[/ATTACH][ATTACH=CONFIG]520370[/ATTACH]And slow we roll..........

Make sure your hatch scoops clear those oil filters lol. There's gotta be a better way to get those turned 90*

Yes:ernaehrung004:

Lookin good stinger. Spring is just around corner.

I wish it felt more like apron this BS sucks already.

36 twin step on ebay right now

Yup that's Rogers boat. Owns a body shop in NH. Boat is also listed here is the classifieds. It's build #1 of the 6/7 made. Runs just about 91/92.

Boat came home last night I'll take and post pics of my slow progress. Life gets in the vest of life. Hope to have the platform off and cleats off today. Throttle shifter set up and indicators off also for red pray. Then start reassembly

[ATTACH=CONFIG]521570[/ATTACH]Out side the shop

Looks nice. Simple/clean

Platform is off rear cleats off going to powder Monday. Platform going red. Want to break it up just a bit

Pulled the rest of the cleats off side panels and seats.
I'm going to thru bolt the seats into the dash since they are just lagged in. The cables for the drives are smoked to those need replacing also. Control assembly is screwed in that will be thru bolted. Last is the anchor locked just screwed in and missing 2 screws so I will thru bolt that as well.

[ATTACH=CONFIG]521575[/ATTACH][ATTACH=CONFIG]521576[/ATTACH][ATTACH=CONFIG]521577[/ATTACH]Couple pics

Of course you must have the apache forward lifts too, Nice!

[ATTACH=CONFIG]521603[/ATTACH]Not sure what the apache foward lifts are but here is a now shot. Anchor locker and cleat removed. Cleat will be resprayed and I'm thru bolting the locker on both sides of the hinge.

The lift you have the boat parked between is a forward with an Indian head on it

Ok so just spent money I don't have boost gauges senders fuel senders 20 LED lights speaks Am/FM radio E12 subs AMP all new hardware and list goes on......

All white stepped 36, or 37 -- one of my favorites! !

Cleaned the bilge tonight pre fit gps, radio, VHF and put battery boxes in. Should have all parts ordered by Friday. Looking for a Sunday motor install. Platform dropped off also cleats for powder coat. Chipping away at it rite now.

[ATTACH=CONFIG]521702[/ATTACH]Lights galore just came in, ordered the sea pump kits fiber washer spring licks for the bell housing side for motor install. Needed a res bottle for trim pump that's on the way also

Ok so the crest of the interior is out doing new flooring and sir panels. Glove box came in ordered another speedo for the pass side. I should have the speakers and boost gauges tomorrow.

Where did you find a glove box? whats it look like?

It's actually a full am fm radio encloser I'm using as a glove

Pulled the flooring up last night and drilled out cabin light holes. Ran wires to them and rewired one light on another switch. Pulled cockpit OE lights out mocked up new lights in side panels and drill for lights in engine bulk head. I'll try to get the engine room lighting done tonight and order new flooring. Thanks to Hess (Dave) for some insight on my abortion of an interior. 1 way or another I'll get it done.

[ATTACH=CONFIG]521979[/ATTACH][ATTACH=CONFIG]521980[/ATTACH][ATTACH=CONFIG]521981[/ATTACH]Slow night tonight just picked up the platform and cleats. Came out mint at the tube of 860. But anyhow they are in and that's about it. Shooting for trim tank engine exhaust block off plate batt boxes and engine room lights tomorrow. We shall see

yikes your powder coat guy isnt shy about the $$$$ next time you need stuff done let me have my guy do it
ill bet it would have been $300 for what you had done .. hell your here every week anyways and comin again thursday
gotta say its starting to take shape ..i prob should have kept it for my self

Want it back......

Boost gauges are in. Ran the sender hoses also last night. Took the trim cables out to get length on them. Threw bolted instrument panel, cabin switch panel, and controls. Ran the wires for the cabin floor lights started on the stereo install. Also threw bolted the steps to get on the deck, not sure why the hell you would only screw those in. Started on fuel lines also.

It kind of sounds like those steps were an after thought? I don't have anything on mine that's not thru bolted. Then again, I don't have the steps anyway but I'd like to add them. Do you have a pic?

Pic of what part frank? I'll grab what ever you want. Going to hit it hard tonight trying to get a motor in by next week at some point.

[ATTACH=CONFIG]522277[/ATTACH][ATTACH=CONFIG]522278[/ATTACH][ATTACH=CONFIG]522279[/ATTACH][ATTACH=CONFIG]522280[/ATTACH][ATTACH=CONFIG]522281[/ATTACH][ATTACH=CONFIG]522282[/ATTACH]Hack wired the cardio to check function of speakers head unit ect. Lights are all hooked up and in place. Vacuumed it just to clean up. Mounted and set up the amp.

[ATTACH=CONFIG]522287[/ATTACH]Frank is this the pic you wanted? Look to the left and right if the entrance, there is steps at staggered Hughes to get up a'top the bow

Does anyone have a fix for the cabin door l. It's tin aluminum and it's beat from the aluminum to the cover. I'm wondering what's the thineat starboard they make. Would this be suitable?

That's it. Thank you.

Mine is stainless steel amd the upholstery is glued to it. When I first bought the boat it was hard to open/close. I called Bobby and he told me to fix it by replacing the edges with car door trim and lube it up with vaseline. Worked like a charm.