Offshoreonly.com - Search Results
Offshoreonly.com

Go Back  Offshoreonly.com > Search Forums
Reload this Page >

Search Results

Register
FAQ
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: ildukhunter
Showing results 1 to 16 of 16
Search took 0.01 seconds.
Forum: Drives and Lower Units
06-04-2012, 10:05 PM
Replies: 2
Views: 2,518
Posted By ildukhunter

Merc has a special tool for adusting the cable. I...

Merc has a special tool for adusting the cable. I only did this when I replaced the cable. It was easy but the drive has to be off to use the tool. I don't about doing this with the drive on.
Forum: Drives and Lower Units
06-04-2012, 09:59 PM
Replies: 8
Views: 1,225
Posted By ildukhunter

Go to the long Island Boaters Club web site,...

Go to the long Island Boaters Club web site, http://www.liboatersclub.com. The have a vidio that shows how to pull the B3 off and put it back on.
Forum: Drives and Lower Units
05-08-2012, 11:15 PM
Replies: 6
Views: 1,848
Posted By ildukhunter

Buy the tool and save yourself grief. It's only...

Buy the tool and save yourself grief. It's only about $30.
Forum: Drives and Lower Units
04-30-2012, 02:10 AM
Replies: 10
Views: 1,699
Posted By ildukhunter

I had to repair the gimbal ring last season and...

I had to repair the gimbal ring last season and while I was at it replaced everything, belows and upper and lower swivel shafts. I used JR Marines method (plate kit) rather then pulling the motor and...
Forum: Drives and Lower Units
04-30-2012, 01:59 AM
Replies: 1
Views: 970
Posted By ildukhunter

I have not used this particular product of Ron's...

I have not used this particular product of Ron's but have purchased other stuff from him and I rate JR marine as top shelf stuff. They are a machine shop and make a lot their own stuff. Call Ron and...
Forum: Drives and Lower Units
07-18-2011, 10:31 AM
Replies: 2
Views: 968
Posted By ildukhunter

Well I checked with the expert, Ron Bender at J-R...

Well I checked with the expert, Ron Bender at J-R Marine and he said use the Loctite .
Forum: Drives and Lower Units
07-17-2011, 04:59 PM
Replies: 2
Views: 968
Posted By ildukhunter

Gimbal Ring Install

I am in the process of putting my J-R Marine gimbal ring in. I am also replacing the upper swival shaft bushing and seal and swival shaft. The Merc shop manual tells me to use Loctite 27131 on the...
Forum: Drives and Lower Units
07-14-2011, 01:46 PM
Replies: 2
Views: 965
Posted By ildukhunter

Thanx for your reply John. I ordered the tools.

Thanx for your reply John. I ordered the tools.
Forum: Drives and Lower Units
07-13-2011, 10:11 AM
Replies: 2
Views: 965
Posted By ildukhunter

B3 Shift Cable Adjustment

I am replacing the shift cable, housing, and bellows on my 97 B3 drive. The shop manual indicated 2 adjustment tools, one on the Bell Housing side and one on the engine side. I hate to buy the tools...
Forum: Drives and Lower Units
06-06-2011, 09:21 AM
Replies: 9
Views: 2,441
Posted By ildukhunter

The hinge pins are also installed with locktite...

The hinge pins are also installed with locktite making them intentially hard to remove. To be safe you should remove the driveshaft bellows first and then you can put the torch on the area around the...
Forum: Drives and Lower Units
04-27-2011, 01:04 AM
Replies: 4
Views: 985
Posted By ildukhunter

I would go with the stainless, less likely to...

I would go with the stainless, less likely to rust, cheaper than Mercs. Why not have Ron fix your gimbal instead of getting a new one? It would save you a lot of money.
Forum: Drives and Lower Units
04-21-2011, 10:46 AM
Replies: 3
Views: 943
Posted By ildukhunter

That sounds logical. I posted the same question...

That sounds logical. I posted the same question on the Bayliner owners site and I found a guy who used a dremmel to remove his. He ground a slit on the opposite side of the one in the original and...
Forum: Drives and Lower Units
04-20-2011, 06:30 PM
Replies: 3
Views: 943
Posted By ildukhunter

Gimbal Housing Question

I need to pull the small bushing for the upper swivel shaft in the gimbal housing. The shop manual (4B-22) indicates a Snap On tool but I checked and it's about $400 plus. Anyone ever done this with...
Forum: Do It Yourself, Boating on a Budget
11-30-2010, 04:02 PM
Replies: 13
Views: 1,945
Posted By ildukhunter

Mrfixall

Did you get my PM?
Forum: Do It Yourself, Boating on a Budget
11-27-2010, 11:04 AM
Replies: 24
Views: 4,957
Posted By ildukhunter

Perko Flush Pro

After putting in a new raw water pump I would also install one of these and forget about the muffs - http://www.perko.com/catalog/category/underwater_hardware/product/62/e
Forum: Do It Yourself, Boating on a Budget
11-25-2010, 01:10 PM
Replies: 13
Views: 1,945
Posted By ildukhunter

Installing Bellows On B3 Drive

Is anybody aware of a good vidio on installing the bellows on the B3 drive. I found some good ones showing how to pull everything off but I have not found any showing the reinstallation. I have to...
Showing results 1 to 16 of 16


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.